Infiniti FX35, FX50 (S51). Manual — part 1065
EXT-10
< PRECAUTION >
PRECAUTIONS
5.
When the repair work is completed, re-connect both battery cables. With the brake pedal released, turn
the push-button ignition switch from ACC position to ON position, then to LOCK position. (The steering
wheel will lock when the push-button ignition switch is turned to LOCK position.)
6.
Perform self-diagnosis check of all control units using CONSULT-III.
Precaution for Procedure without Cowl Top Cover
INFOID:0000000005248853
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc.
Precaution for Work
INFOID:0000000005248854
• After removing and installing the opening/closing parts, be sure to carry out fitting adjustments to check their
operation.
• Check the lubrication level, damage, and wear of each part. If necessary, grease or replace it.
PIIB3706J
PREPARATION
EXT-11
< PREPARATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000005248855
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tools
INFOID:0000000005248856
Tool number
(Kent-Moore No.)
Tool name
Description
(J-39570)
Chassis ear
Locates the noise
(J-43980)
NISSAN Squeak and Rattle
Kit
Repairing the cause of noise
SIIA0993E
SIIA0994E
Tool name
Description
Engine ear
Locates the noise
Remover tool
Removes clips, pawls and metal clips
Power tool
SIIA0995E
PIIB7923J
PIIB1407E
EXT-12
< REMOVAL AND INSTALLATION >
FRONT BUMPER
REMOVAL AND INSTALLATION
FRONT BUMPER
Exploded View
INFOID:0000000005248857
JMKIA2694ZZ
FRONT BUMPER
EXT-13
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
Removal and Installation
INFOID:0000000005248858
REMOVAL
CAUTION:
Bumper fascia is made of resin. Never apply strong force to it, and be careful to prevent contact with
oil.
1.
Fully open hood assembly.
2.
Remove front bumper fascia assembly upper side fixing clips
(A).
3.
Remove engine room covers (LH/RH) (For VK engine models). Refer to
.
4.
Remove hood seal assemblies (LH/RH) (1) fixing clips (A), and
then remove hood seal assembly located on the front area.
Refer to
DLK-245, "Removal and Installation"
5.
Remove bolts (A) of fixing bumper side stiffener (1) and front
fender (LH/RH).
1.
Bumper side bracket RH
2.
Bumper reinforcement
3.
Energy absorber
4.
Bumper side stiffener RH
5.
Front grille
6.
Front emblem
7.
Front fog lamp finisher RH
8.
Front fog lamp RH
9.
Bumper fascia assembly lower
10. Front fog lamp finisher LH
11.
Front fog lamp LH
12. License plate bracket
13. Sonar sensor RH
14.
Bumper fascia assembly
15. Sonar sensor LH
16. Bumper side grommet RH
17.
Front camera finisher
18. Bumper side grommet LH
19. Bumper side stiffener LH
20.
Hood top seal
21. Bumper side bracket LH
JMKIA2695ZZ
JMKIA2696ZZ
: Vehicle front
JMKIA2697ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст