Infiniti FX35, FX50 (S51). Manual — part 1573
GLASS LID
RF-73
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
1.
Remove the inner blind.
2.
Remove the TORX bolts (A).
3.
Remove the glass lid from the vehicle.
INSTALLATION
CAUTION:
After installing the glass lid, perform the leak test and check that there is no malfunction.
NOTE:
After installation perform fitting adjustment. Refer to
Install in the reverse order of removal.
Adjustment
INFOID:0000000005248646
LID WEATHER-STRIP OVERLAP ADJUSTMENT AND SURFACE MISMATCH ADJUSTMENT
1.
Tilt up glass lid, and then remove lnner blind (left and right).
2.
After loosening glass lid from TORX bolts (left and right), tilt down glass lid.
3.
Adjust glass lid from outside of vehicle so it resembles “A – A” “B – B” “C – C” as shown in the figure.
4.
To prevent glass lid from moving after adjustment, first tighten the TORX bolts of front left, and then
tighten the TORX bolts of rear right.
5.
Tighten remaining TORX bolts, being careful to prevent glass lid from moving.
6.
Tilt glass lid up and down several times to check that it moves smoothly.
NOTE:
JMKIA2690ZZ
PIIB3117J
Portion
a (Wether-strip overlap)
b (Surface height)
Glass lid front end
A – A
0.6 – 2.2 mm (0.024 – 0.087 in)
−
0.7 – 2.3 mm (
−
0.028 – 0.091 in)
Glass lid side end
B – B
0.6 – 2.2 mm (0.024 – 0.087 in)
−
0.7 – 2.3 mm (
−
0.028 – 0.091 in)
Glass lid rear end
C – C
0.6 – 2.2 mm (0.024 – 0.087 in)
−
0.7 – 2.3 mm (
−
0.028 – 0.091 in)
RF-74
< REMOVAL AND INSTALLATION >
GLASS LID
After adjusting the sunroof unit assembly, perform additional service. Refer to
WHEN REPLACING CONTROL UNIT : Special Repair Requirement"
.
SUNROOF MOTOR ASSEMBLY
RF-75
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
SUNROOF MOTOR ASSEMBLY
Exploded View
INFOID:0000000005248647
Removal and Installation
INFOID:0000000005248648
REMOVAL
CAUTION:
• Before removing sunroof motor, check that glass lid is fully closed.
• After removing sunroof motor, never attempt to rotate sunroof motor assembly as a single unit.
1.
Remove the map lamp assembly. Refer to
INL-183, "Removal and Installation"
1.
Glass lid
2.
TORX bolt
3.
Inner blind (LH/RH)
4.
Drain hose (front)
5.
Drain connector (front)
6.
Sunroof motor assembly
7.
Sunroof front bracket (LH/RH)
8.
Sunroof rear bracket (LH/RH)
9.
Drain hose (rear)
10. Drain connector (rear)
11.
Sunroof unit assembly
Refer to
JMKIA2688GB
RF-76
< REMOVAL AND INSTALLATION >
SUNROOF MOTOR ASSEMBLY
2.
Remove the sunroof motor assembly.
• Disconnect connector (A) from sunroof motor assembly (1).
• Remove sunroof motor assembly mounting screws (B), and
then remove sunroof motor assembly.
INSTALLATION
CAUTION:
Before installing the sunroof motor assembly, always place the link and wire assembly in the symmet-
rical and fully closed position.
1.
Move the sunroof motor assembly laterally a little so that the gear is completely engaged into the wire on
the sunroof unit assembly and mounting surface becomes parallel. Then tighten the sunroof motor
assembly with screws.
2.
Install the map lamp assembly. Refer to
INL-183, "Removal and Installation"
.
JMKIA2691ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст