Infiniti FX35, FX50 (S51). Manual — part 521
WELCOME LIGHT FUNCTION DOES NOT OPERATE
DLK-207
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
WELCOME LIGHT FUNCTION DOES NOT OPERATE
Description
INFOID:0000000005239671
NOTE:
• Before performing the diagnosis following procedure, check “Work Flow”. Refer to
• Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and
check each symptom.
CONDITIONS OF VEHICLE (OPERATION CONDITIONS)
• Intelligent Key system (door lock function) is normal.
• All operation conditions are satisfied. Refer to
DLK-33, "WELCOME LIGHT FUNCTION : System Descrip-
Diagnosis Procedure
INFOID:0000000005239672
1.
CHECK WELCOME LIGHT FUNCTION SETTING
Check “WELCOME LIGHT OP SET” and “WELCOME LIGHT SELECT” setting in “WORK SUPPORT”. Refer
to
DLK-54, "INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY)"
.
Is the function active?
YES
>> GO TO 2.
NO
>> Set “WELCOME LIGHT OP SET” and “WELCOME LIGHT SELECT” setting in “WORK SUP-
PORT”.
2.
CHECK DOOR LOCK FUNCTION
Check Intelligent Key system (door lock function).
Does the door lock/unlock using door request switch (driver side)?
YES
>> GO TO 3.
NO
>> Go to
DLK-197, "DRIVER SIDE : Description"
3.
CHECK INTERIOR ROOM LAMP CONTROL SYSTEM
Check interior room lamp control system. Refer to
Does the room lamp and puddle lamp turn ON?
YES
>> GO TO 4.
NO
>> Go to
4.
REPLACE BCM
BCS-83, "Removal and Installation"
.
>> GO TO 5.
5.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> INSPECTION END
NO
>> GO TO 1.
DLK-208
< SYMPTOM DIAGNOSIS >
PANIC ALARM FUNCTION DOES NOT OPERATE
PANIC ALARM FUNCTION DOES NOT OPERATE
Description
INFOID:0000000005239673
NOTE:
• Before performing the diagnosis following procedure, check “Work Flow”. Refer to
• Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and
check each symptom.
CONDITIONS OF VEHICLE (OPERATION CONDITIONS)
• Ignition switch is in the OFF or LOCK position.
• Intelligent Key is removed from key slot.
Diagnosis Procedure
INFOID:0000000005239674
1.
CHECK REMOTE KEYLESS ENTRY FUNCTION
Check remote keyless entry function.
Does door lock/unlock with Intelligent key button?
YES
>> GO TO 2.
NO
>> Go to
.
2.
CHECK VEHICLE SECURITY ALARM OPERATION
Check vehicle security alarm operation.
Does alarm (headlamp and horn) activate?
YES
>> GO TO 3.
NO
>> Go to
.
3.
CHECK “PANIC ALARM SET” SETTING IN “WORK SUPPORT”
Check “PANIC ALARM SET” setting in “WORK SUPPORT”.
Refer to
DLK-54, "INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY)"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Set “PANIC ALARM SET” setting in “WORK SUPPORT”.
4.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-36, "Intermittent Incident"
.
NO
>> GO TO 1.
HAZARD AND HORN REMINDER DOES NOT OPERATE
DLK-209
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
HAZARD AND HORN REMINDER DOES NOT OPERATE
Description
INFOID:0000000005239675
NOTE:
• Before performing the diagnosis following procedure, check “Work Flow”. Refer to
• Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and
check each symptom.
CONDITIONS OF VEHICLE (OPERATION CONDITIONS)
• Ignition switch is in the OFF or LOCK position.
• Intelligent Key is removed from key slot.
Diagnosis Procedure
INFOID:0000000005239676
1.
CHECK “HAZARD ANSWER BACK” SETTING IN “WORK SUPPORT”
Check “HAZARD ANSWER BACK” setting in “WORK SUPPORT”.
Refer to
DLK-54, "INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY)"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Set “HAZARD ANSWER BACK” setting in “WORK SUPPORT”.
2.
CHECK “HORN WITH KEYLESS LOCK” SETTING IN “WORK SUPPORT”.
Check “HORN WITH KEYLESS LOCK” setting in “WORK SUPPORT”.
Refer to
DLK-54, "INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY)"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Set “HORN WITH KEYLESS LOCK” setting in “WORK SUPPORT”.
3.
CHECK HAZARD WARNING LAMP
Check hazard warning lamp.
Refer to
DLK-110, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunctioning parts.
4.
CHECK HORN
Check horn.
Refer to
DLK-105, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace the malfunctioning parts.
5.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-36, "Intermittent Incident"
.
NO
>> GO TO 1.
DLK-210
< SYMPTOM DIAGNOSIS >
HAZARD AND BUZZER REMINDER DOES NOT OPERATE
HAZARD AND BUZZER REMINDER DOES NOT OPERATE
Description
INFOID:0000000005239677
NOTE:
• Before performing the diagnosis in the following procedure, check “Work Flow”. Refer to
• Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and
check each symptom.
CONDITIONS OF VEHICLE (OPERATING CONDITIONS)
• Intelligent Key is removed from key slot.
• Ignition switch is in the OFF position.
• No Intelligent Keys are inside the vehicle.
Diagnosis Procedure
INFOID:0000000005239678
1.
CHECK “HAZARD ANSWER BACK” SETTING IN “WORK SUPPORT”
Check “HAZARD ANSWER BACK” setting in “WORK SUPPORT”.
Refer to
DLK-53, "DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK)"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Set “HAZARD ANSWER BACK” in “WORK SUPPORT”.
2.
CHECK “ANS BACK I-KEY LOCK” SETTING IN “WORK SUPPORT”
Check “ANS BACK I-KEY LOCK” setting in “WORK SUPPORT”.
Refer to
DLK-53, "DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK)"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Set “ANS BACK I-KEY LOCK” in “WORK SUPPORT”.
3.
CHECK “ANS BACK I-KEY UNLOCK” SETTING IN “WORK SUPPORT”
Check “ANS BACK I-KEY UNLOCK” setting in “WORK SUPPORT”.
Refer to
DLK-53, "DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK)"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Set “ANS BACK I-KEY UNLOCK” in “WORK SUPPORT”.
4.
CHECK HAZARD WARNING LAMP
Check hazard warning lamp.
Refer to
DLK-110, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace the malfunctioning parts.
5.
CHECK INTELLIGENT KEY WARNING BUZZER
Check Intelligent Key warning buzzer.
Refer to
DLK-97, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace the malfunctioning parts.
6.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-36, "Intermittent Incident"
.
NO
>> GO TO 1.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст