Infiniti FX35, FX50 (S51). Manual — part 325
CCS-120
< DTC/CIRCUIT DIAGNOSIS >
[ICC (FULL SPEED RANGE)]
C1A40 SYSTEM SWITCH CIRCUIT
Special Repair Requirement
INFOID:0000000005501689
DESCRIPTION
Perform the action test after adjusting the laser beam aiming of ICC sensor integrated unit when the following
operation is performed.
• Removal and installation of ICC sensor integrated unit
• Replacement of ICC sensor integrated unit
SPECIAL REPAIR REQUIREMENT
1.
LASER BEAM AIMING ADJUSTMENT OF ICC SENSOR INTEGRATED UNIT
Adjust the laser beam aiming of the ICC sensor integrated unit. Refer to
>> GO TO 2.
2.
CHECK ICC SYSTEM
1.
Erase the “Self Diagnostic Result”, and then perform “All DTC Reading” again after performing the action
test. (Refer to
CCS-18, "ACTION TEST : Description"
2.
Check that the ICC system is normal.
>> WORK END
CCS
U0121 VDC CAN 2
CCS-121
< DTC/CIRCUIT DIAGNOSIS >
[ICC (FULL SPEED RANGE)]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
U0121 VDC CAN 2
Description
INFOID:0000000005501690
ABS actuator and electric unit (control unit) transmits the VDC system signal to ICC sensor integrated unit via
CAN communication.
DTC Logic
INFOID:0000000005501691
DTC DETECTION LOGIC
NOTE:
If DTC “U0121” is detected along with DTC “U1000”, first diagnose the DTC “U1000”. Refer to
.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Start the engine.
2.
Turn the MAIN switch of ICC system ON.
3.
Perform “All DTC Reading” with CONSULT-III.
4.
Check if the “U0121” is detected as the current malfunction in “Self Diagnostic Result” of “ICC”.
Is “U0121” detected as the current malfunction?
YES
>> Refer to
CCS-121, "Diagnosis Procedure"
NO
>> Refer to
GI-36, "Intermittent Incident"
.
Diagnosis Procedure
INFOID:0000000005501692
1.
CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000” is detected other than “U0121” in “Self Diagnostic Result” of “ICC”.
Is “U1000” detected?
YES
>> Perform the CAN communication system inspection. Repair or replace the malfunctioning parts.
.
NO
>> GO TO 2.
2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS RESULTS
Check if any DTC is detected in “Self Diagnostic Result” of “ABS”.
Is any DTC detected?
YES
>> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
NO
>> Replace the ICC sensor integrated unit. Refer to
Special Repair Requirement
INFOID:0000000005501693
DESCRIPTION
Perform the action test after adjusting the laser beam aiming of ICC sensor integrated unit when the following
operation is performed.
• Removal and installation of ICC sensor integrated unit
• Replacement of ICC sensor integrated unit
SPECIAL REPAIR REQUIREMENT
DTC
(On board dis-
play)
Trouble diagnosis name
DTC detecting condition
Possible causes
U0121
(127)
VDC CAN CIR2
If ICC sensor integrated unit detects an error
signal that is received from ABS actuator and
electric unit (control unit) via CAN communica-
tion
ABS actuator and electric unit (control
unit)
CCS-122
< DTC/CIRCUIT DIAGNOSIS >
[ICC (FULL SPEED RANGE)]
U0121 VDC CAN 2
1.
LASER BEAM AIMING ADJUSTMENT OF ICC SENSOR INTEGRATED UNIT
Adjust the laser beam aiming of the ICC sensor integrated unit. Refer to
>> GO TO 2.
2.
CHECK ICC SYSTEM
1.
Erase the “Self Diagnostic Result”, and then perform “All DTC Reading” again after performing the action
test. (Refer to
CCS-18, "ACTION TEST : Description"
2.
Check that the ICC system is normal.
>> WORK END
CCS
U0126 STRG SEN CAN 1
CCS-123
< DTC/CIRCUIT DIAGNOSIS >
[ICC (FULL SPEED RANGE)]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
U0126 STRG SEN CAN 1
Description
INFOID:0000000005501694
It measures the rotation amount, rotation speed, and rotation direction of steering wheel, and then transmits
them to ICC sensor integrated unit via CAN communication.
DTC Logic
INFOID:0000000005501695
DTC DETECTION LOGIC
NOTE:
If DTC “U0126” is detected along with DTC “U1000”, first diagnose the DTC “U1000”. Refer to
.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Start the engine.
2.
Turn the MAIN switch of ICC system ON.
3.
Perform “All DTC Reading” with CONSULT-III.
4.
Check if the “U0126” is detected as the current malfunction in “Self Diagnostic Result” of “ICC”.
Is “U0126” detected as the current malfunction?
YES
>> Refer to
CCS-123, "Diagnosis Procedure"
NO
>> Refer to
GI-36, "Intermittent Incident"
.
Diagnosis Procedure
INFOID:0000000005501696
1.
CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000” is detected other than “U0126” in “Self Diagnostic Result” of “ICC”.
Is “U1000” detected?
YES
>> Perform the CAN communication system inspection. Repair or replace the malfunctioning parts.
.
NO
>> GO TO 2.
2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS RESULTS
Check if any DTC is detected in “Self Diagnostic Result” of “ABS”.
Is any DTC detected?
YES
>> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
NO
>> Replace the ICC sensor integrated unit. Refer to
Special Repair Requirement
INFOID:0000000005501697
DESCRIPTION
Perform the action test after adjusting the laser beam aiming of ICC sensor integrated unit when the following
operation is performed.
• Removal and installation of ICC sensor integrated unit
• Replacement of ICC sensor integrated unit
SPECIAL REPAIR REQUIREMENT
1.
LASER BEAM AIMING ADJUSTMENT OF ICC SENSOR INTEGRATED UNIT
DTC
(On board dis-
play)
Trouble diagnosis name
DTC detecting condition
Possible causes
U0126
(130)
STRG SEN CAN CIR1
If ICC sensor integrated unit detects an error
signal that is received from steering angle sen-
sor via CAN communication
Steering angle sensor error
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст