Infiniti FX35, FX50 (S51). Manual — part 601
DRIVE PINION
DLN-239
< UNIT DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: R200]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
2WD : Disassembly
INFOID:0000000005249248
1.
Remove differential case assembly. Refer to
2.
Remove drive pinion lock nut with the flange wrench.
3.
Put matching mark (B) on the end of drive pinion. The matching
mark should be in line with the matching mark (A) on companion
flange (1).
CAUTION:
For matching mark, use paint. Never damage companion
flange and drive pinion.
NOTE:
The matching mark on the final drive companion flange indicates
the maximum vertical runout position.
When replacing companion flange, matching mark is not neces-
sary.
4.
Remove companion flange using the suitable pullers.
5.
Press drive pinion assembly out of gear carrier.
CAUTION:
Never drop drive pinion assembly.
6.
Remove front oil seal.
7.
Remove side oil seal.
8.
Remove pinion front bearing inner race.
9.
Remove collapsible spacer.
JSDIA0033ZZ
JSDIA0016ZZ
JSDIA0034ZZ
PDIA0760J
DLN-240
< UNIT DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: R200]
DRIVE PINION
10. Remove pinion rear bearing inner race and pinion height adjust-
ing washer with the replacer (A) (commercial service tool).
11. Tap pinion front/rear bearing outer races uniformly using a brass
rod or equivalent to remove them.
CAUTION:
Never damage gear carrier.
2WD : Assembly
INFOID:0000000005249249
1.
Install front bearing outer race (1) and rear bearing outer race
(2) using drifts.
CAUTION:
• At first, using a hammer, tap bearing outer race until it
becomes flat to gear carrier.
• Never reuse pinion front and rear bearing outer race.
2.
Select drive pinion height adjusting washer. Refer to
PDIA0801J
SDIA0817E
A
: Drift [SST: ST30720000 (J-25405)]
B
: Drift [SST: KV40105230 (
—
)]
C
: Drift bar [SST: ST30611000 (J-25742-1)]
D
: Drift [SST: ST30613000 (J-25742-3)]
PDIA0761J
DRIVE PINION
DLN-241
< UNIT DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: R200]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
3.
Install selected drive pinion height adjusting washer (2) to drive
pinion. Press pinion rear bearing inner race (1) to it, using drift
(A) [SST: ST30901000 (J-26010-01)].
CAUTION:
• Be careful of the direction of pinion height adjusting
washer. (Assemble as shown in the figure.)
• Never reuse pinion rear bearing inner race.
4.
Assemble collapsible spacer to drive pinion.
CAUTION:
Never reuse collapsible spacer.
5.
Apply gear oil to pinion rear bearing, and assemble drive pinion
into gear carrier.
6.
Apply gear oil to pinion front bearing, and assemble pinion front
bearing inner race to drive pinion assembly.
CAUTION:
Never reuse pinion front bearing inner race.
7.
Using suitable spacer (A), press the pinion front bearing inner
race to drive pinion as far as drive pinion nut can be tightened.
8.
Using the drift (A) [SST: ST30720000 (J-25405)], install front oil
seal as shown in figure.
CAUTION:
• Never reuse oil seal.
• When installing, never incline oil seal.
• Apply multi-purpose grease onto oil seal lips, and gear oil
onto the circumference of oil seal.
9.
Install companion flange (1).
NOTE:
When reusing drive pinion, align the matching mark (B) of drive
pinion with the matching mark (A) of companion flange, and then
install companion flange (1).
PDIA0805J
PDIA0492E
PDIA0762J
PDIA0764J
JSDIA0016ZZ
DLN-242
< UNIT DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: R200]
DRIVE PINION
10. Apply anti-corrosion oil to the thread and seat of drive pinion
lock nut, and temporarily tighten drive pinion lock nut to drive
pinion.
CAUTION:
Never reuse drive pinion lock nut.
11. Adjust to the drive pinion lock nut tightening torque and pinion
bearing preload torque.
CAUTION:
• Adjust to the lower limit of the drive pinion lock nut tight-
ening torque first.
• If the preload torque exceeds the specified value, replace
collapsible spacer and tighten it again to adjust. Never
loosen drive pinion lock nut to adjust the preload torque.
• After adjustment, rotate drive pinion back and forth 2 to 3
times to check for unusual noise, rotation malfunction,
and other malfunctions.
12. Install differential case assembly. Refer to
CAUTION:
Never install rear cover at this timing.
13. Check and adjust drive gear runout, tooth contact, drive gear to drive pinion backlash, and companion
flange runout. Refer to
and
Recheck above items. Readjust the above description, if necessary.
14. Check total preload torque. Refer to
.
15. Install rear cover. Refer to
2WD : Adjustment
INFOID:0000000005249250
PINION GEAR HEIGHT
1.
Make sure all parts are clean and that the bearings are well
lubricated.
2.
Assemble the pinion gear bearings into the differential shim
selector tool [SST:
—
(J-34309)].
A
: Preload gauge [SST: ST3127S000 (J-25765-A)]
Standard
Pinion bearing preload
: Refer to
JSDIA0035ZZ
SPD769
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст