Infiniti FX35, FX50 (S51). Manual — part 1068
EXT-22
< REMOVAL AND INSTALLATION >
COWL TOP
COWL TOP
Exploded View
INFOID:0000000005248863
1.
Front fender cover RH
2.
Cowl top cover RH
3.
Battery cover
4.
Hoodledge cover RH
5.
Cowl top cover seal RH
6.
Cowl top cover seal LH
7.
Hoodledge cover LH
8.
Brake master cylinder cover
9.
Cowl top cover RH
10. Front fender cover LH
11. Cowl top seal
12. EPT sealer
: Clip
JMKIA2716ZZ
COWL TOP
EXT-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
Removal and Installation
INFOID:0000000005248864
REMOVAL
1.
Fully open hood assembly.
2.
Remove front wiper arms and blades (LH/RH) from vehicle. Refer to
WW-120, "Removal and Installation"
.
3.
Remove battery cover and brake master cylinder cover.
4.
Remove cowl top cover seals (LH/RH).
5.
Remove hoodledge cover mounting clips and then remove hoodledge covers (LH/RH).
6.
Remove front fender covers (1) fixing clips (LH/RH).
7.
Remove cowl top seal.
8.
Remove cowl top covers (LH/RH) fixing clips.
9.
Push pawls (A) and (B) to remove cowl top cover RH (1) as
shown in the figure.
10. Push pawl (A) as shown by the arrow in the figure to remove
cowl top cover LH (1).
INSTALLATION
Note the following itmes, and install in the reverse order of removal.
: Pawl
Refer to
for symbols in the figure.
: Clip
JMKIA2237ZZ
JMKIA2717ZZ
JMKIA2159ZZ
EXT-24
< REMOVAL AND INSTALLATION >
COWL TOP
• Align concave of cowl top cover RH (1) to windshield glass (2) pin
(A) as shown in the figure when installing.
• Slide the pawl while aligning with the concave part of (C).
• Engage the joint of pawl of (A) with (B), and then assemble cowl
top covers LH (1) and RH (2).
CAUTION:
• Always replace EPT sealer with a new one, if the cowl top cover is reused.
• After installing, perform adjustment of wiper arm. Refer to
.
JMKIA2160ZZ
JMKIA2161ZZ
FENDER PROTECTOR
EXT-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
FENDER PROTECTOR
FENDER PROTECTOR
FENDER PROTECTOR : Exploded View
INFOID:0000000005248865
FENDER PROTECTOR : Removal and Installation
INFOID:0000000005248866
REMOVAL
1.
Remove front fillet molding. Refer to
EXT-32, "Removal and Installation"
2.
Remove front fender protectors (front and rear side) fixing grom-
mets (A) with a remover tool (B).
1.
Splash guard (AWD models)
2.
Fender protector (front)
3.
J-nut
4.
Front fender
5.
Grommet
6.
Fender clip
7.
Fender protector (rear)
JMKIA2718ZZ
JMKIA2719ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст