Infiniti FX35, FX50 (S51). Manual — part 211
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-25
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
ACTIVE TEST
FLASHER
FLASHER : CONSULT-III Function (BCM - FLASHER)
INFOID:0000000005612694
WORK SUPPORT
*: Factory setting
DATA MONITOR
RR WIPER STOP
[Off/On]
Rear wiper motor (stop position) status input from the rear wiper motor.
H/L WASH SW
[Off/On]
NOTE:
The item is indicated, but not monitored.
Monitor Item
[Unit]
Description
Test item
Operation
Description
FR WIPER
Hi
Transmits the front wiper request signal (HI) to IPDM E/R with CAN communication to operate the
front wiper HI operation.
Lo
Transmits the front wiper request signal (LO) to IPDM E/R with CAN communication to operate the
front wiper LO operation.
INT
Transmits the front wiper request signal (INT) to IPDM E/R with CAN communication to operate the
front wiper INT operation.
Off
Stops transmitting the front wiper request signal to stop the front wiper operation.
RR WIPER
On
Outputs the voltage to operate the rear wiper motor.
Off
Stops the voltage to stop.
Service item
Setting item
Setting
HAZARD ANSWER
BACK
Lock/Unlk*
With locking/unlocking
Sets the hazard warning lamp answer back function
when the door is lock/unlock with the request switch or
the key fob.
Unlk Only
With unlocking only
Lock Only
With locking only
Off
Without the function
Monitor item
[Unit]
Description
REQ SW-DR
[On/Off]
The switch status input from the request switch (driver side)
REQ SW-AS
[On/Off]
The switch status input from the request switch (passenger side)
PUSH SW
[On/Off]
The switch status input from the push-button ignition switch
TURN SIGNAL R
[On/Off]
Each switch condition that BCM judges from the combination switch reading function
TURN SIGNAL L
[On/Off]
HAZARD SW
[On/Off]
The switch status input from the hazard switch
RKE-LOCK
[On/Off]
Lock signal status received from the remote keyless entry receiver
BCS-26
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
ACTIVE TEST
INTELLIGENT KEY
INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY)
INFOID:0000000005612687
WORK SUPPORT
RKE-UNLOCK
[On/Off]
Unlock signal status received from the remote keyless entry receiver
RKE-PANIC
[On/Off]
Panic alarm signal status received from the remote keyless entry receiver
Monitor item
[Unit]
Description
Test item
Operation
Description
FLASHER
Off
Stops the voltage to turn the turn signal lamps OFF.
LH
Outputs the voltage to blink the left side turn signal lamps.
RH
Outputs the voltage to blink the right side turn signal lamps.
Monitor item
Description
REMO CONT ID CONFIR
It can be checked whether Intelligent Key ID code is registered or not in this mode.
AUTO LOCK SET
Auto door lock time can be changed in this mode.
• MODE 1: 1 min.
• MODE 2: 5 min.
• MODE 3: 30 sec.
• MODE 4: 2 min.
WELCOME LIGHT OP SET
Welcome light function mode can be changed to operate (WITH) or not operate (WITHOUT)
in this mode.
LOCK/UNLOCK BY I-KEY
Door lock/unlock function by door request switch (driver side, passenger side and back door)
mode can be changed to operate (WITH) or not operate (WITHOUT) in this mode.
ENGINE START BY I-KEY
Engine start function mode can be changed to operate (WITH) or not operate (WITHOUT) in
this mode.
TRUNK/GLASS HATCH OPEN
Buzzer reminder function mode by back door request switch can be changed to operate (ON)
or not operate (OFF) in this mode.
PANIC ALARM SET
Panic alarm button pressing time on Intelligent Key remote control button can be selected from
the following in this mode.
• MODE 1: 0.5 sec.
• MODE 2: Non-operational
• MODE 3: 1.5 sec.
PW DOWN SET
Unlock button pressing time on Intelligent Key button can be selected from the following in this
mode.
• MODE 1: 3 sec.
• MODE 2: Non-operational
• MODE 3: 5 sec.
TRUNK OPEN DELAY
NOTE:
This item is displayed, but cannot be supported.
LO- BATT OF KEY FOB WARN
Intelligent Key low battery warning mode can be changed to operate (WITH) or not operate
(WITHOUT) with this mode.
ANTI KEY LOCK IN FUNCTI
Key reminder function mode can be changed to operate (WITH) or not operate (WITHOUT)
with this mode.
HAZARD ANSWER BACK
Hazard reminder function mode can be selected from the following in this mode.
• LOCK ONLY: Door lock operation only
• UNLOCK ONLY: Door unlock operation only
• LOCK/UNLOCK: Lock/unlock operation
• OFF: Non-operational
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-27
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
SELF-DIAG RESULT
DATA MONITOR
ANS BACK I-KEY LOCK
Buzzer reminder function (lock operation) mode by door request switch (driver side and pas-
senger side) can be selected from the following in this mode.
• Horn chirp: Sound horn
• Buzzer: Sound Intelligent Key warning buzzer
• OFF: Non-operational
ANS BACK I-KEY UNLOCK
Buzzer reminder function (unlock operation) mode by door request switch can be changed to
operate (ON) or not operate (OFF) in this mode.
SHORT CRANKING OUTPUT
Starter motor can operate during the times below.
• 70 msec.
• 100 msec.
• 200 msec.
INSIDE ANT DIAGNOSIS
This function allows inside key antenna self-diagnosis.
HORN WITH KEYLESS LOCK
Horn reminder function mode by Intelligent Key button can be changed to operate (ON) or not
operate (OFF) in this mode.
WELCOME LIGHT SELECT
Welcome light function mode can be selected from the following in this mode.
• Puddle Lamp (ON/OFF)
• Room Lamp (ON/OFF)
• Head and Tail Lamps (This item is displayed, but cannot be supported.)
• Outside Handle (This item is displayed, but cannot be supported.)
Monitor item
Description
Monitor Item
Condition
REQ SW -DR
Indicates [ON/OFF] condition of door request switch (driver side).
REQ SW -AS
Indicates [ON/OFF] condition of door request switch (passenger side).
REQ SW -BD/TR
Indicates [ON/OFF] condition of back door request switch.
PUSH SW
Indicates [ON/OFF] condition of push-button ignition switch.
IGN RLY2 -F/B
Indicates [ON/OFF] condition of ignition relay 2.
CLUCH SW
NOTE:
This item is displayed, but cannot be monitored.
BRAKE SW 1
Indicates [ON/OFF] condition of brake switch.
DETE/CANCL SW
Indicates [ON/OFF] condition of the P position.
SFT PN/N SW
Indicates [ON/OFF] condition of the P or N position.
S/L -LOCK
Indicates [ON/OFF] condition of steering lock unit (LOCK).
S/L -UNLOCK
Indicates [ON/OFF] condition of steering lock unit (UNLOCK).
S/L RELAY -F/B
Indicates [ON/OFF] condition of ignition switch.
UNLK SEN -DR
Indicates [ON/OFF] condition of driver door UNLOCK status.
PUSH SW -IPDM
Indicates [ON/OFF] condition of push-button ignition switch.
IGN RLY1 -F/B
Indicates [ON/OFF] condition of ignition relay 1.
DETE SW -IPDM
Indicates [ON/OFF] condition of the P position.
SFT PN -IPDM
Indicates [ON/OFF] condition of the P or N position.
SFT P -MET
Indicates [ON/OFF] condition of the P position.
SFT N -MET
Indicates [ON/OFF] condition of the N position.
ENGINE STATE
Indicates [STOP/START/CRANK/RUN] condition of engine states.
S/L LOCK-IPDM
Indicates [ON/OFF] condition of steering lock unit (LOCK).
S/L UNLK-IPDM
Indicates [ON/OFF] condition of steering lock unit (UNLOCK).
S/L RELAY-REQ
Indicates [ON/OFF] condition of steering lock relay.
BCS-28
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
ACTIVE TEST
VEH SPEED 1
Displays the vehicle speed signal received from unified meter and A/C amp. by numerical
value [Km/h].
VEH SPEED 2
Displays the vehicle speed signal received from ABS or VDC or CVT by numerical value
[Km/h].
DOOR STAT-DR
Indicates [LOCK/READY/UNLOCK] condition of driver side door status.
DOOR STAT-AS
Indicates [LOCK/READY/UNLOCK] condition of passenger side door status.
ID OK FLAG
Indicates [SET/RESET] condition of key ID.
PRMT ENG STRT
Indicates [SET/RESET] condition of engine start possibility.
PRMT RKE STRT
NOTE:
This item is displayed, but cannot be monitored.
KEY SW -SLOT
Indicates [ON/OFF] condition of key slot.
TRNK/HAT MNTR
NOTE:
This item is displayed, but cannot be monitored.
RKE-LOCK
Indicates [ON/OFF] condition of LOCK signal from Intelligent Key.
RKE-UNLOCK
Indicates [ON/OFF] condition of UNLOCK signal from Intelligent Key.
RKE-TR/BD
NOTE:
This item is displayed, but cannot be monitored.
RKE-PANIC
Indicates [ON/OFF] condition of PANIC button of Intelligent Key.
RKE-P/W OPEN
Indicates [ON/OFF] condition of P/W DOWN signal from Intelligent Key.
RKE-MODE CHG
Indicates [ON/OFF] condition of MODE CHANGE signal from Intelligent Key.
RKE OPE COUN1
When remote keyless entry receiver receives the signal transmitted while operating on In-
telligent Key, the numerical values starts changing.
RKE OPE COUN2
NOTE:
This item is displayed, but cannot be monitored.
Monitor Item
Condition
Test item
Description
BATTERY SAVER
This test is able to check interior room lamp operation.
The interior room lamp is activated when “ON” on CONSULT-III screen is touched.
PW REMOTO DOWN SET
This test is able to check power window down operation.
The power window down is activated when “ON” on CONSULT-III screen is touched.
OUTSIDE BUZZER
This test is able to check Intelligent Key warning buzzer operation.
The Intelligent Key warning buzzer is activated when “ON” on CONSULT-III screen is touched.
INSIDE BUZZER
This test is able to check warning chime in combination meter operation.
• Takes away warning chime sounds when “TAKE OUT” on CONSULT-III screen is touched.
• Key warning chime sounds when “KEY” on CONSULT-III screen is touched.
• The P position warning chime sounds when “KNOB” on CONSULT-III screen is touched.
INDICATOR
This test is able to check warning lamp operation.
• “KEY” Warning lamp illuminates when “RED ON” on CONSULT-III screen is touched.
• The “KEY” Warning lamp blinks when “RED IND” on CONSULT-III screen is touched.
INT LAMP
This test is able to check interior room lamp operation.
The interior room lamp is activated when “ON” on CONSULT-III screen is touched.
LCD
This test is able to check meter display information
• Engine start information displays when “BP N” on CONSULT-III screen is touched.
• Engine start information displays when “BP I” on CONSULT-III screen is touched.
• Key ID warning displays when “ID NG” on CONSULT-III screen is touched.
• Steering lock information displays when “ROTAT” on CONSULT-III screen is touched.
• The P position warning displays when “SFT P” on CONSULT-III screen is touched.
• Intelligent Key insert information displays when “INSRT” on CONSULT-III screen is touched.
• Intelligent Key low battery warning displays when “BATT” on CONSULT-III screen is touched.
• Take away through window warning displays when “NO KY” on CONSULT-III screen is touched.
• Take away warning displays when “OUTKY” on CONSULT-III screen is touched.
• The OFF position warning displays when “LK WN” on CONSULT-III screen is touched.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст