Infiniti FX35, FX50 (S51). Manual — part 210
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-21
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
*: Factory setting
DATA MONITOR
Service item
Setting item
Setting
SET I/L D-UNLCK INTCON
On*
Interior room lamps link with door unlock.
(Interior room lamp timer function)
Off
Interior room lamps do not link with door unlock.
ROOM LAMP TIMER SET
MODE 2
7.5 sec.
Interior room lamp ON time after door are unlocked.
MODE 3*
15 sec.
MODE 4
30 sec.
ROOM LAMP ON TIME SET
MODE 1
NOTE:
The item is indicated, but not used.
MODE 2
MODE 3
MODE 4
MODE 5*
ROOM LAMP OFF TIME SET
MODE 1
NOTE:
The item is indicated, but not used.
MODE 2
MODE 3
MODE 4
MODE 5*
R LAMP TIMER LOGIC SET
MODE 1*
Interior room lamp timer activates by synchronizing all doors.
MODE 2
Interior room lamp timer activates by synchronizing the driver door
only.
Monitor item
[Unit]
Description
REQ SW-DR
[On/Off]
The switch status input from request switch (driver side)
REQ SW-AS
[On/Off]
The switch status input from request switch (passenger side)
REQ SW-RR
[On/Off]
NOTE:
The item is indicated, but not monitored.
REQ SW-RL
[On/Off]
PUSH SW
[On/Off]
The switch status input from push-button ignition switch
UNLK SEN-DR
[On/Off]
Driver door unlock status input from unlock sensor
KEY SW-SLOT
[On/Off]
Key switch status input from key slot
DOOR SW-DR
[On/Off]
The switch status input from front door switch (driver side)
DOOR SW-AS
[On/Off]
The switch status input from front door switch (passenger side)
DOOR SW-RR
[On/Off]
The switch status input from rear door switch (RH)
DOOR SW- RL
[On/Off]
The switch status input from rear door switch (LH)
DOOR SW-BK
[On/Off]
The switch status input from back door switch
BCS-22
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
ACTIVE TEST
HEADLAMP
HEADLAMP : CONSULT-III Function (BCM - HEAD LAMP)
INFOID:0000000005612693
WORK SUPPORT
*: Factory setting
CDL LOCK SW
[On/Off]
Lock switch status received from central door lock/unlock switch by power window
switch serial link
CDL UNLOCK SW
[On/Off]
Unlock switch status received from central door lock/unlock switch by power window
switch serial link
KEY CYL LK-SW
[On/Off]
Lock switch status received from key cylinder lock/unlock switch by power window
switch serial link
KEY CYL UN-SW
[On/Off]
Unlock switch status received from key cylinder lock/unlock switch by power window
switch serial link
TRNK/HAT MNTR
[On/Off]
The switch status input from trunk room lamp switch
RKE-LOCK
[On/Off]
Lock signal status received from remote keyless entry receiver
RKE-UNLOCK
[On/Off]
Unlock signal status received from remote keyless entry receiver
Monitor item
[Unit]
Description
Test item
Operation
Description
INT LAMP
On
Outputs the room lamp timer signal to the total illumination control unit to activate in-
terior room lamps. (Hospitality lighting functioning table “Scene 1”)
Off
Stops the room lamp timer signal.
STEP LAMP TEST
On
Outputs the step lamp control signal to turn step lamp ON.
Off
Stops the step lamp control signal to turn step lamp OFF.
LUGGAGE LAMP TEST
On
NOTE:
The item is indicated, but not used.
Off
Service item
Setting item
Setting
CUSTOM A/LIGHT SET-
TING
MODE 1*
Normal
MODE 2
More sensitive setting than normal setting (Turns ON earlier than normal operation.)
MODE 3
More sensitive setting than MODE 2 (Turns ON earlier than MODE 2.)
MODE 4
Less sensitive setting than normal setting (Turns ON later than normal operation.)
BATTERY SAVER SET
On*
With the exterior lamp battery saver function
Off
Without the exterior lamp battery saver function
ILL DELAY SET
MODE 1*
45 sec.
Sets delay timer function timer operation time.
(All doors closed)
MODE 2
Without the func-
tion
MODE 3
30 sec.
MODE 4
60 sec.
MODE 5
90 sec.
MODE 6
120 sec.
MODE 7
150 sec.
MODE 8
180 sec.
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-23
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
DATA MONITOR
ACTIVE TEST
Monitor item
[Unit]
Description
PUSH SW
[On/Off]
The switch status input from push-button ignition switch
ENGINE STATE
[Stop/Stall/Crank/Run]
The engine status received from ECM with CAN communication
VEH SPEED 1
[km/h]
The value of the vehicle speed received from unified meter and A/C amp. with CAN
communication
KEY SW-SLOT
[On/Off]
Key switch status input from key slot
TURN SIGNAL R
[On/Off]
Each switch status that BCM judges from the combination switch reading function
TURN SIGNAL L
[On/Off]
TAIL LAMP SW
[On/Off]
HI BEAM SW
[On/Off]
HEAD LAMP SW1
[On/Off]
HEAD LAMP SW2
[On/Off]
PASSING SW
[On/Off]
AUTO LIGHT SW
[On/Off]
FR FOG SW
[On/Off]
DOOR SW-DR
[On/Off]
The switch status input from front door switch (driver side)
DOOR SW-AS
[On/Off]
The switch status input from front door switch (passenger side)
DOOR SW-RR
[On/Off]
The switch status input from rear door switch RH
DOOR SW- RL
[On/Off]
The switch status input from rear door switch LH
DOOR SW-BK
[On/Off]
NOTE:
The item is indicated, but not monitored.
OPTICAL SENSOR
[V]
The value of exterior brightness voltage input from the optical sensor
Test item
Operation
Description
TAIL LAMP
On
Transmits the position light request signal to IPDM E/R with CAN com-
munication to turn the tail lamp ON.
Off
Stops the position light request signal transmission.
HEAD LAMP
Hi
Transmits the high beam request signal with CAN communication to turn
the headlamp (HI).
Low
Transmits the low beam request signal with CAN communication to turn
the headlamp (LO).
Off
Stops the high & low beam request signal transmission.
BCS-24
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
WIPER
WIPER : CONSULT-III Function (BCM - WIPER)
INFOID:0000000005612698
WORK SUPPORT
*:Factory setting
DATA MONITOR
FR FOG LAMP
On
Transmits the front fog light request signal to IPDM E/R with CAN com-
munication to turn the front fog lamp ON.
Off
Stops the front fog light request signal transmission.
RR FOG LAMP
On
NOTE:
The item is indicated, but cannot be tested.
Off
CORNERING LAMP
RH
NOTE:
The item is indicated, but cannot be tested.
LH
Off
ILL DIM SIGNAL
On
NOTE:
The item is indicated, but cannot be tested.
Off
Test item
Operation
Description
Service item
Setting item
Description
WIPER SPEED
SETTING
On
With vehicle speed
(Front wiper intermittent time linked with the vehicle speed and wiper intermittent dial position)
Off*
Without vehicle speed
(Front wiper intermittent time linked with the wiper intermittent dial position)
Monitor Item
[Unit]
Description
PUSH SW
[Off/On]
The switch status input from push-button ignition switch.
VEHICLE SPEED 1
[km/h]
The value of the vehicle speed signal received from unified meter and A/C amp. with CAN communication.
FR WIPER HI
[Off/On]
Each switch status that BCM judges from the combination switch reading function.
FR WIPER LOW
[Off/On]
FR WASHER SW
[Off/On]
FR WIPER INT
[Off/On]
FR WIPER STOP
[Off/On]
Front wiper motor (stop position) status received from IPDM E/R with CAN communication.
INT VOLUME
[1
−
7]
Each switch status that BCM judges from the combination switch reading function.
RR WIPER ON
[Off/On]
Each switch status that BCM judges from the combination switch reading function.
RR WIPER INT
[Off/On]
RR WASHER SW
[Off/On]
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст