Infiniti FX35, FX50 (S51). Manual — part 1762
ST-40
< REMOVAL AND INSTALLATION >
POWER STEERING OIL PUMP
16. Apply recommended fluid to O-ring, and then install O-ring to body assembly.
17. Install suction pipe to body assembly.
VQ35HR : Inspection
INFOID:0000000005235289
RELIEF OIL PRESSURE
CAUTION:
Make sure that belt tension is normal before starting the following procedure.
1.
Connect the oil pressure gauge [SST: KV48103500 (J-26357)]
and the oil pressure gauge adapter [SST: KV48102500 (J-
33914)] between oil pump discharge connector and high-pres-
sure hose. Bleed air from the hydraulic circuit while opening
valve fully. Refer to
.
2.
Start engine. Run engine until oil temperature reaches 50 to
80
°
C (122 to 176
°
F).
CAUTION:
• Leave the valve of the oil pressure gauge fully open while
starting and running engine. If engine is started with the
valve closed, the hydraulic pressure in oil pump goes up
to the relief pressure along with unusual increase of oil
temperature.
• Be sure to keep hose clear of belts and other parts when
engine is started.
3.
Fully close the oil pressure gauge valve with engine at idle and
measure the relief oil pressure.
CAUTION:
Never keep valve closed for 10 seconds or longer.
4.
Open the valve slowly after measuring. Repair oil pump if the relief oil pressure is outside the standard.
Refer to
ST-37, "VQ35HR : Disassembly and Assembly"
5.
Disconnect the oil pressure gauge from hydraulic circuit.
6.
When installing eye bolt (1) and copper washer (2) to oil pump
(3), refer to the figure.
CAUTION:
• Never reuse copper washers.
• Apply power steering fluid or equivalent to around copper
washer, then install eye bolt.
• Install eye bolt with eye joint (assembled to high pressure
hose) (B) protrusion (A) facing with pump side cutout, and
then tighten it to the specified torque after tightening by
hand. Refer to
ST-48, "VQ35HR : Exploded View"
(VQ35HR),
ST-49, "VK50VE : Exploded View"
• Securely insert harness connector to pressure sensor.
7.
Check fluid level, fluid leakage and air bleeding hydraulic system after the installation. Refer to
BEFORE DISASSEMBLY
Disassemble oil pump only when the following malfunctions occur.
• If oil leakage is found on oil pump.
• Oil pump pulley is damaged or deformed.
• Performance of oil pump is low.
AFTER DISASSEMBLY
Body Assembly and Rear Cover Inspection
Standard
Relief oil pressure
: Refer to
.
SGIA0915E
JSGIA0452ZZ
POWER STEERING OIL PUMP
ST-41
< REMOVAL AND INSTALLATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
Check body assembly and rear cover for internal damage. Replace rear cover if it is damaged. Replace oil
pump assembly if body assembly is damaged.
Cartridge Assembly Inspection
Check cam ring, rotor and vane for damage. Replace cartridge assembly if necessary.
Side Plate Inspection
Check side plate for damage. Replace side plate if there are.
Flow Control Valve Inspection
Check flow control valve and spring for damage. Replace if necessary.
VK50VE
VK50VE : Exploded View
INFOID:0000000005235290
REMOVAL
DISASSEMBLY
1.
Power steering oil pump
2.
Bracket
: Vehicle front
Refer to
JSGIA0411GB
ST-42
< REMOVAL AND INSTALLATION >
POWER STEERING OIL PUMP
VK50VE : Removal and Installation
INFOID:0000000005235291
REMOVAL
1.
Drain power steering fluid from reservoir tank.
2.
Remove the floor under cover from vehicle. Refer to
3.
Loosen drive belt. Refer to
4.
Remove drive belt from oil pump pulley.
5.
Remove pressure sensor connector.
6.
Remove joint mounting nut.
7.
Remove suction hose (drain fluid from their pipings).
8.
Remove oil pump mounting bolts, and then remove oil pump.
INSTALLATION
Note the following, and install in the reverse order of removal.
1.
Pulley
2.
Snap ring
3.
Drive shaft
4.
Joint
5.
O-ring 6.
Connector
bolt
7.
Flow control valve
8.
Spring
9.
Oil seal
10. Suction pipe
11.
O-ring
12. Body assembly
13. O-ring
14. Side plate
15. Vane
16. Rotor
17. Cam ring
18. Cartridge
19. Dowel pin
20. Gasket
21. Rear cover
22. Copper washer
: Apply power steering fluid.
: Apply multi-purpose grease.
Refer to
for symbols not described on the above.
SGIA1187E
POWER STEERING OIL PUMP
ST-43
< REMOVAL AND INSTALLATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
• When installing suction hoses (1), refer to the figure.
CAUTION:
• Never apply fluid to the hose (1) and tube (2).
• Insert hose securely until it contacts spool (A) of tube.
• Leave clearance (L) when installing clamp (3).
• When installing eye bolt (1) and copper washer (2) to oil pump (3),
refer to the figure.
CAUTION:
• Never reuse copper washer.
• Apply power steering fluid to around copper washers, then
install eye bolt.
• Install eye bolt with eye joint (assembled to high pressure
hose) (B) protrusion (A) facing with pump side cutout, and
then tighten it to the specified torque after tightening by
hand. Refer to
ST-49, "VK50VE : Exploded View"
• Securely insert harness connector to pressure sensor.
• About the installation of drive belt. Refer to
• Check fluid level, fluid leakage and air bleeding hydraulic system after the installation. Refer to
VK50VE : Disassembly and Assembly
INFOID:0000000005235292
DISASSEMBLY
NOTE:
Secure oil pump in a vise if necessary.
CAUTION:
Use copper plates when securing in a vise.
1.
Remove rear cover mounting bolts, and then remove rear cover from body assembly.
2.
Remove gasket from body assembly.
3.
Remove dowel pin, cartridge and side plate from body assembly.
4.
Remove pulley mounting nut and washer, then remove pulley from drive shaft.
5.
Remove snap ring from drive shaft and press out it.
CAUTION:
When removing snap ring, be careful not to damage drive
shaft.
Standard
L
: 3 – 8 mm (0.12 – 0.31 in)
JSGIA0118ZZ
JSGIA0452ZZ
SST010B
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст