Infiniti FX35, FX50 (S51). Manual — part 1644
SE-96
< REMOVAL AND INSTALLATION >
REAR SEAT
Remove the clips.
2.
Remove the armrest assembly. (RH seat only)
• Remove the hog lings, and then pull the seatback trim.
• Remove the metal clips and pawl, and then pull out armrest
bracket cover.
• Remove the mounting bolts (A), and then remove the armrest
bracket (1).
• Remove the armrest assembly.
3.
Remove the reclining device cover.
Remove the screws (A) and clip (B), and then reclining device
inner cover (1) and reclining device inner cover inside (2).
4.
Remove the reclining lever knob assembly.
: Clip
JMJIA2086ZZ
: Metal clip
: Pawl
JMJIA2087ZZ
JMJIA2088ZZ
JMJIA2089ZZ
REAR SEAT
SE-97
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
• Remove the push nut (1), cable resin part (2) and cable clamp
(3).
• Remove the hog rings (A) and cable clamp.
• Remove the reclining lever knob cap.
• Remove the screw (B), and then remove reclining knob lever
assembly (4).
5.
Remove the seatback trim and pad.
• Remove the seatback hinge outer cover.
• Remove the mounting bolt (A) and then remove seatback
hinge.
• Remove the hog rings from back side.
• Remove the seatback retainer.
• Remove the seat belt finisher. Refer to
SB-11, "SEAT BELT RETRACTOR : Removal and Installation"
.
JMJIA2090ZZ
JMJIA2091ZZ
JMJIA2092ZZ
JMJIA2093ZZ
SE-98
< REMOVAL AND INSTALLATION >
REAR SEAT
• Remove the headrest holder.
CAUTION:
Before installing headrest holder check its orientation.
(front/rear and right/left)
• Remove the seatback trim and pad.
• Remove the hog rings to separate the seatback trim and seatback pad.
6.
Remove the reclining device (LH). (LH seat only)
Remove the mounting bolts (A), and then remove reclining
device (LH).
7.
Remove the dynamic damper.
Remove the dynamic damper mounting nuts (A).
8.
Remove the seat belt hook.
9.
Remove the rear center seat belt retractor. Refer to
SB-11, "SEAT BELT RETRACTOR : Removal and
.
Assembly
Assemble in the reverse order of disassembly.
CAUTION:
• Always slacken cable end and link pin when installing reclin-
ing lever knob cable.
PIIB8351J
JMJIA2322ZZ
JMJIA2094ZZ
JMJIA2320ZZ
REAR SEAT
SE-99
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
• Always install in the position that the reclining device lock
can be released, because cable resin part is adjustable (3
stages).
• Install the hog rings of seatback trim in position, and then securely connect the trim or trim cord with
the seatback frame.
SEAT CUSHION
Disassembly
Remove the hog rings to separate the trim and pad.
Assembly
Assemble in the reverse order of disassembly.
CAUTION:
Install the hog rings of seat cushion trim in position, and then securely connect the trim or trim cord
with the seat cushion pad wire.
ARMREST
Disassembly
1.
Remove the cup holder.
Remove the metal clips and pawls.
2.
Remove the armrest lid assembly.
Remove the mounting screw.
3.
Remove the armrest strap.
• Open the fastener (1), and then pull up armrest trim.
JMJIA2321ZZ
: Pawl
: Metal clip
JMJIA2099ZZ
JMJIA2100ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст