Infiniti FX35, FX50 (S51). Manual — part 1642
SE-88
< REMOVAL AND INSTALLATION >
FRONT SEAT
• Remove the pawls, and then remove side support bag (1).
• Remove the side support unit (2).
Assembly
Assemble in the reverse order of disassembly.
CAUTION:
Install the hog rings of seatback trim in position, and then securely connect the trim or trim cord with
the pad side wire.
SEAT CUSHION
Disassembly
1.
Remove the seatback board.
• Remove the clips, and then pull out seatback board.
• Pull down the seatback board to release the upper pawls.
2.
Remove the seat cushion front finisher.
Remove the metal clips and pawls, pull out seat cushion front
finisher.
3.
Remove the seat cushion outer finisher.
• Remove the clip, metal clips and pawls, and then pull out seat
cushion outer finisher.
• Remove the connector clamps, and then disconnect harness
connectors.
4.
Remove the seat cushion outer finisher inside (front and rear).
: Pawl
JMJIA2031ZZ
: Clip
: Pawl
JMJIA2024ZZ
: Metal clip
: Pawl
JMJIA2032ZZ
: Clip
: Metal clip
: Pawl
JMJIA2025ZZ
FRONT SEAT
SE-89
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
5.
Remove the seat cushion inner finisher.
Remove the metal clip and pawls, and then pull out seat cushion
inner finisher.
6.
Remove the seat cushion inner finisher inside (front and rear).
7.
Remove the seatback trim retainer and seatback trim band from seat cushion frame.
8.
Remove the seatback assembly.
• Remove the side air bag module harness (A).
• Cut the seatback duct band (1) of seat cushion under side.
• Disconnect the side support air hose joint (2).
• Disconnect the reclining motor harness connector (B).
• Disconnect the lumbar support unit harness connector (C).
• Disconnect the side support unit harness connector (D).
• Disconnect the thermal electric device (TED) harness connec-
tor (E).
• Pull out harness from the seatback trim and seat cushion trim.
: Metal clip
: Pawl
JMJIA2026ZZ
JMJIA2027ZZ
JMJIA2028ZZ
JMJIA2029ZZ
SE-90
< REMOVAL AND INSTALLATION >
FRONT SEAT
• Remove the seatback assembly mounting bolts (F).
9.
Remove the seat belt buckle. Refer to
SB-8, "SEAT BELT BUCKLE : Removal and Installation"
.
10. Remove the seat cushion pad (front). (Thigh extension model only.)
• Remove the retainer.
• Remove the seat cushion pad (front).
11. Remove the seat cushion trim and seat cushion pad.
• Remove the seat cushion trim wire (1) from the hook (2).
(Thigh extension model only.)
• Remove the clip (A). (Thigh extension model only.)
• Remove the seat cushion retainer.
• Disconnect the seat cushion heater unit harness connector.
• Remove the hog rings, and separate the seat cushion trim and seat cushion pad.
12. Remove the seat cushion side support bag. (Side support model only.)
• Remove the hose clamp.
JMJIA2030ZZ
JMJIA0019ZZ
JMJIA2034ZZ
JMJIA2035ZZ
FRONT SEAT
SE-91
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
• Remove the pawls, and then remove side support bag (1).
13. Remove the metal clips and pawl, and then pull out seat cushion
outer lower finisher outside (1) and inside (2).
14. Remove the seat cushion inner lower finisher.
15. Remove the driver seat control unit (Automatic drive positioner model only). Refer to
Assembly
Assemble in the reverse order of disassembly.
CAUTION:
Install the hog rings of seat cushion trim in position, and then securely connect the trim or trim cord
with the pad side wire.
CLIMATE CONTROLLED SEAT UNIT
Disassembly
1.
Remove the seatback duct and seatback thermal electric device (TED).
Remove the screws (A), and then cut the band (1).
: Pawl
JMJIA2036ZZ
: Metal clip
: Pawl
JMJIA2037ZZ
: Metal clip
JMJIA2038ZZ
JMJIA2039ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст