Infiniti FX35, FX50 (S51). Manual — part 716
P1551, P1552 BATTERY CURRENT SENSOR
EC-405
< DTC/CIRCUIT DIAGNOSIS >
[VQ35HR]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace battery negative cable assembly.
EC-406
< DTC/CIRCUIT DIAGNOSIS >
[VQ35HR]
P1553 BATTERY CURRENT SENSOR
P1553 BATTERY CURRENT SENSOR
Description
INFOID:0000000005237011
The power generation voltage variable control enables fuel consumption to be decreased by reducing the
engine load which is caused by the power generation of the generator. The battery current sensor is installed
to the battery cable at the negative terminal. The sensor measures the charging/discharging current of the bat-
tery. Based on the sensor signal, ECM judges whether or not the power generation voltage variable control is
performed. When performing the power generation voltage variable control, ECM calculates the target power
generation voltage based on the sensor signal. And ECM sends the calculated value as the power generation
command value to IPDM E/R. For the details of the power generation voltage variable control, refer to
CAUTION:
Never connect the electrical component or the ground wire directly to the battery terminal. The con-
nection causes the malfunction of the power generation voltage variable control, and then battery dis-
charge may occur.
DTC Logic
INFOID:0000000005237012
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1.
Turn ignition switch OFF and wait at least 10 seconds.
2.
Turn ignition switch ON.
3.
Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 8 V at idle.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Start engine and wait at least 10 seconds.
2.
Check 1st trip DTC.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P1553
Battery current sensor perfor-
mance
The signal voltage transmitted from the
sensor to ECM is higher than the amount
of the maximum power generation.
• Harness or connectors
(Battery current sensor circuit is open
or shorted.)
[Crankshaft position (CKP) sensor cir-
cuit is shorted.]
[Camshaft position (CMP) sensor
(bank 2) circuit is shorted.]
[Exhaust valve timing (EVT) control po-
sition sensor (bank 2) circuit is short-
ed.]
[Accelerator pedal position (APP) sen-
sor 2 circuit is shorted.]
(EVAP control system pressure sensor
circuit is shorted.)
(Refrigerant pressure sensor circuit is
shorted.)
• Battery current sensor
• CKP sensor
• CMP sensor (bank 2)
• EVT control position sensor (bank 2)
• APP sensor
• EVAP control system pressure sensor
• Refrigerant pressure sensor
P1553 BATTERY CURRENT SENSOR
EC-407
< DTC/CIRCUIT DIAGNOSIS >
[VQ35HR]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
Is 1st trip DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000005237013
1.
CHECK GROUND CONNECTION
1.
Turn ignition switch OFF.
2.
Check ground connection M95. Refer to Ground Inspection in
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace ground connection.
2.
CHECK BATTERY CURRENT SENSOR POWER SUPPLY CIRCUIT-I
1.
Disconnect battery current sensor harness connector.
2.
Turn ignition switch ON.
3.
Check the voltage between battery current sensor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> GO TO 3.
3.
CHECK BATTERY CURRENT SENSOR POWER SUPPLY CIRCUIT-II
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check the continuity between battery current sensor harness connector and ECM harness connector.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 4.
4.
DETECT MALFUNCTIONING PART
Check the following.
• Harness connectors F1, E3
• Harness for open between battery current sensor and ECM
>> Repair open circuit.
5.
CHECK SENSOR POWER SUPPLY CIRCUIT
Check harness for short to power and short to ground, between the following terminals.
Battery current sensor
Ground
Voltage (V)
Connector
Terminal
E21
1
Ground
Approx. 5
Battery current sensor
ECM
Continuity
Connector
Terminal
Connector
Terminal
E21
1
F102
64
Existed
ECM
Sensor
Connector
Terminal
Name
Connector
Terminal
F101
46
Crankshaft position (CKP) sensor
F2
1
F102
64
Camshaft position (CMP) sensor (bank 2)
F18
1
Exhaust valve timing (EVT) control posi-
tion sensor (bank 2)
F19
1
Battery current sensor
E21
1
EC-408
< DTC/CIRCUIT DIAGNOSIS >
[VQ35HR]
P1553 BATTERY CURRENT SENSOR
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair short to ground or short to power in harness or connectors.
6.
CHECK COMPONENTS
Check the following.
• CKP sensor (Refer to
EC-271, "Component Inspection"
• CMP sensor (bank 2) (Refer to
EC-277, "Component Inspection"
.)
• EVT position sensor (bank 2) (Refer to
EC-369, "Component Inspection"
.)
• EVAP control system pressure sensor (Refer to
EC-313, "Component Inspection"
.)
• Refrigerant pressure sensor (Refer to
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Replace malfunctioning component.
7.
CHECK APP SENSOR
EC-444, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 14.
NO
>> GO TO 8.
8.
REPLACE ACCELERATOR PEDAL ASSEMBLY
1.
Replace accelerator pedal assembly.
2.
Go to
EC-445, "Special Repair Requirement"
.
>> INSPECTION END
9.
CHECK BATTERY CURRENT SENSOR GROUND CIRCUIT FOR OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check the continuity between battery current sensor harness connector and ECM harness connector.
4.
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 11.
NO
>> GO TO 10.
10.
DETECT MALFUNCTIONING PART
Check the following.
• Harness connectors F1, E3
• Harness for open or short between battery current sensor and ECM
>> Repair open circuit, short to ground or short to power in harness or connectors.
M107
103
Accelerator pedal position (APP) sensor
E112
(Without ICC)
6
E116
(With ICC)
3
107
EVAP control system pressure sensor
B252
3
111
Refrigerant pressure sensor
E77
3
ECM
Sensor
Connector
Terminal
Name
Connector
Terminal
Battery current sensor
ECM
Continuity
Connector
Terminal
Connector
Terminal
E21
2
F102
95
Existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст