Infiniti FX35, FX50 (S51). Manual — part 446
OVERHEATING CAUSE ANALYSIS
CO-29
< SYMPTOM DIAGNOSIS >
[VK50VE]
C
D
E
F
G
H
I
J
K
L
M
A
CO
N
P
O
SYMPTOM DIAGNOSIS
OVERHEATING CAUSE ANALYSIS
Troubleshooting Chart
INFOID:0000000005246381
Symptom
Check items
Cooling sys-
tem parts
malfunction
Poor heat transfer
Water pump malfunction
Worn or loose drive belt
—
Thermostat stuck closed
—
Damaged fins
Dust contamination or pa-
per clogging
Physical damage
Clogged radiator cooling
tube
Excess foreign material
(rust, dirt, sand, etc.)
Reduced air flow
Cooling fan does not oper-
ate
Fan assembly
—
High resistance to fan rota-
tion
Damaged fan blades
Damaged radiator shroud
—
—
—
Improper engine coolant
mixture ratio
—
—
—
Poor engine coolant quality
—
Engine coolant density
—
Insufficient engine coolant
Engine coolant leakage
Cooling hose
Loose clamp
Cracked hose
Water pump
Poor sealing
Radiator cap
Loose
Poor sealing
Radiator
O-ring for damage, deterio-
ration or improper fitting
Cracked radiator tank
Cracked radiator core
Reservoir tank
Cracked reservoir tank
Overflowing reservoir tank
Exhaust gas leakage into
cooling system
Cylinder head deterioration
Cylinder head gasket deteri-
oration
CO-30
< SYMPTOM DIAGNOSIS >
[VK50VE]
OVERHEATING CAUSE ANALYSIS
Except cool-
ing system
parts mal-
function
—
Overload on engine
Abusive driving
High engine rpm under no
load
Driving in low gear for ex-
tended time
Driving at extremely high
speed
Powertrain system malfunc-
tion
—
Installed improper size
wheels and tires
Dragging brakes
Improper ignition timing
Blocked or restricted air
flow
Blocked bumper
—
—
Blocked radiator grille
Installed car brassiere
Mud contamination or paper
clogging
Blocked radiator
—
Blocked condenser
Blocked air flow
Installed large fog lamp
Symptom
Check items
PRECAUTIONS
CO-31
< PRECAUTION >
[VK50VE]
C
D
E
F
G
H
I
J
K
L
M
A
CO
N
P
O
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000005550565
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIR BAG”.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s)
with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly
causing serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
CO-32
< PREPARATION >
[VK50VE]
PREPARATION
PREPARATION
PREPARATION
Commercial Service Tools
INFOID:0000000005246383
Tool name
Description
Power tool
Loosening bolts and nuts
Radiator cap tester
Checking radiator and radiator cap
Radiator cap tester adapter
Adapting radiator cap tester to radiator cap
and water inlet filler neck
a: 28 (1.10) dia.
b: 31.4 (1.236) dia.
c: 41.3 (1.626) dia.
Unit: mm (in)
PBIC0190E
PBIC1982E
S-NT564
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст