Infiniti FX35, FX50 (S51). Manual — part 593
REAR FINAL DRIVE ASSEMBLY
DLN-207
< UNIT REMOVAL AND INSTALLATION >
[REAR FINAL DRIVE: R200]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
UNIT REMOVAL AND INSTALLATION
REAR FINAL DRIVE ASSEMBLY
2WD
2WD : Exploded View
INFOID:0000000005249233
2WD : Removal and Installation
INFOID:0000000005249234
REMOVAL
1.
Remove center muffler with a power tool. Refer to
2.
Remove stabilizer bar with a power tool. Refer to
3.
Remove rear propeller shaft from the final drive. Refer to
4.
Remove drive shaft from final drive with a power tool. Then sus-
pend it by wire, etc. Refer to
.
5.
Remove breather hose from the final drive.
6.
Remove rear wheel sensor. Refer to
.
1.
Rear final drive assembly
2.
Upper stopper
3.
Lower stopper
4.
Washer
: Vehicle front
Refer to
JPDID0127GB
SDIA1094E
DLN-208
< UNIT REMOVAL AND INSTALLATION >
[REAR FINAL DRIVE: R200]
REAR FINAL DRIVE ASSEMBLY
7.
Set a suitable jack to rear final drive assembly.
CAUTION:
Never place a jack on the rear cover (aluminum case).
8.
Remove the mounting bolts and nuts connecting to the suspen-
sion member with a power tool. And then, remove rear final
drive assembly.
CAUTION:
Secure rear final drive assembly to a suitable jack while
removing it.
INSTALLATION
Note the following, and installation is in the reverse order of removal.
CAUTION:
Check that there are no pinched or restricted areas on the breather hose caused by bending or wind-
ing when installing it.
• Install the breather hose (1) to breather connector until dimension
(A) shown as follows.
CAUTION:
• Never reuse hose clamp.
• Install the hose clamp at the final drive side, with the tab fac-
ing downward.
• Install the hose clamp at the suspension member side, with the tab facing downward.
• If remove breather connector, install breather hose (1) as shown in
the figure.
- For installation, insert the resin connector into rear suspension
member (2). Install the metal connector (3) in rear cover so that a
paint mark becomes forward of the vehicle as shown in the figure.
Insert the hose clip (4) into rear suspension member. Arrange the
breather hose to pass by over wheel sensor harness.
CAUTION:
Never reuse breather connector and hose clip.
• When oil leaks while removing final drive assembly, check oil level
after the installation. Refer to
AWD
JSDIA0026ZZ
A:
Final drive side
: 20 mm (0.79 in)
Suspension member
side
: 20.5 mm (0.807 in)
: Vehicle front
JPDID0020ZZ
JPDID0269ZZ
REAR FINAL DRIVE ASSEMBLY
DLN-209
< UNIT REMOVAL AND INSTALLATION >
[REAR FINAL DRIVE: R200]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
AWD : Exploded View
INFOID:0000000005249235
AWD : Removal and Installation
INFOID:0000000005249236
REMOVAL
1.
Remove center muffler with a power tool. Refer to
2.
Remove stabilizer bar with a power tool. Refer to
3.
Remove rear propeller shaft from the final drive. Refer to
.
4.
Remove drive shaft from final drive with a power tool. Then sus-
pend it by wire, etc. Refer to
.
5.
Remove breather hose from the final drive.
6.
Remove rear wheel sensor. Refer to
.
7.
Set a suitable jack to rear final drive assembly.
CAUTION:
Never place a jack on the rear cover (aluminum case).
8.
Remove the mounting bolts and nuts connecting to the suspen-
sion member, and remove rear final drive assembly with a power
tool.
CAUTION:
Secure rear final drive assembly to a suitable jack while
removing it.
INSTALLATION
1.
Rear final drive assembly
2.
Upper stopper
3.
Lower stopper
4.
Washer
: Vehicle front
Refer to
JPDID0203GB
SDIA1094E
JSDIA0131ZZ
DLN-210
< UNIT REMOVAL AND INSTALLATION >
[REAR FINAL DRIVE: R200]
REAR FINAL DRIVE ASSEMBLY
Note the following, and installation is in the reverse order of removal.
CAUTION:
Check that there are no pinched or restricted areas on the breather hose caused by bending or wind-
ing when installing it.
• Install the breather hose (1) to breather connector until dimension
(A) shown as follows.
CAUTION:
• Never reuse hose clamp.
• Install the hose clamp at the final drive side, with the tab fac-
ing downward.
• Install the hose clamp at the suspension member side, with the tab facing downward.
• If remove breather connector, install breather hose (1) as shown in
the figure.
- For installation, insert the resin connector into rear suspension
member (2). Install the metal connector (3) in rear cover so that a
paint mark becomes forward of the vehicle as shown in the figure.
Insert the hose clip (4) into rear suspension member. Arrange the
breather hose to pass by over wheel sensor harness.
CAUTION:
Never reuse breather connector and hose clip.
• When oil leaks while removing final drive assembly, check oil level
after the installation. Refer to
A:
Final drive side
: 20 mm (0.79 in)
Suspension member
side
: 20.5 mm (0.807 in)
: Vehicle front
JPDID0020ZZ
JPDID0269ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст