Infiniti FX35, FX50 (S51). Manual — part 1707
CRASH ZONE SENSOR
SR-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
CRASH ZONE SENSOR
Exploded View
INFOID:0000000005249836
Removal and Installation
INFOID:0000000005249837
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
• Never use the air tools or the electric tools for servicing.
REMOVAL
1.
Remove the air duct (inlet).
• VQ35 engine: Refer to
• VK50 engine: Refer to
2.
Remove the reservoir tank.
• VQ35 engine: Refer to
• VK50 engine: Refer to
.
1.
Crash zone sensor
: Vehicle front
Refer to
for symbols in the figure.
JMHIA0663GB
SR-22
< REMOVAL AND INSTALLATION >
CRASH ZONE SENSOR
3.
Disconnect crash zone sensor harness connector (A).
4.
Remove the crash zone sensor (1) fixing nuts (B).
5.
Remove the crash zone sensor.
CAUTION:
• Replace the crash zone sensor of deployed the SRS driver air bag and deployed the SRS front pas-
senger air bag.
• Never impact the crash zone sensor.
• Replace the crash zone sensor if it has been dropped or sus-
tained an impact.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Never use the old fixing nuts after removal, replace with the new nuts.
• Never damage the harness while installing.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT-III. Refer to
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
JMHIA0664ZZ
JMHIA0009ZZ
SIDE AIR BAG (SATELLITE) SENSOR
SR-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
SIDE AIR BAG (SATELLITE) SENSOR
Exploded View
INFOID:0000000005249838
Removal and Installation
INFOID:0000000005249839
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
• Never use the air tools or the electric tools for servicing.
REMOVAL
1.
Remove the front seat belt retractor. Refer to
SB-6, "SEAT BELT RETRACTOR : Removal and Installa-
2.
Remove the satellite sensor (1) fixing nuts (B).
3.
Disconnect the harness connector (A), and then remove the sat-
ellite sensor.
CAUTION:
• Replace the satellite sensor of deployed the SRS front side air bag module and deployed the SRS
side curtain air bag module.
JMHIA0665GB
1.
Satellite sensor
: Vehicle front
Refer to
for symbols in the figure.
JMHIA0666ZZ
SR-24
< REMOVAL AND INSTALLATION >
SIDE AIR BAG (SATELLITE) SENSOR
• Never impact the satellite sensor.
• Replace the satellite sensor if it has been dropped or sus-
tained an impact.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Never use the old fixing nuts after removal, replace with the new nuts.
• Never damage the harness while installing.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT-III. Refer to
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
JMHIA0009ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст