Infiniti FX35, FX50 (S51). Manual — part 1706
FRONT PASSENGER AIR BAG MODULE
SR-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
FRONT PASSENGER AIR BAG MODULE
Exploded View
INFOID:0000000005249832
Removal and Installation
INFOID:0000000005249833
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
• Always work from the side of air bag module. Never work in front of it.
• Never use the air tools or the electric tools for servicing.
REMOVAL
1.
Remove the instrument panel assembly. Refer to
IP-12, "Removal and Installation"
.
2.
Remove the passenger air bag module (1) fixing screws (A).
1.
Passenger air bag module
2.
Instrument panel assembly
: Vehicle front
Refer to
JMHIA0658GB
JMHIA0659ZZ
SR-18
< REMOVAL AND INSTALLATION >
FRONT PASSENGER AIR BAG MODULE
3.
Disconnect pawls by using remover tool (A), and then remove
the front passenger air bag module (1) from the instrument
panel (2).
CAUTION:
• Always place the passenger air bag module with pad side fac-
ing upward.
• Never impact the passenger air bag module.
• Replace the passenger air bag module if it has been dropped
or sustained an impact.
• Never insert any foreign objects (screwdriver, etc.) into the passenger air bag module.
• Never disassemble the passenger air bag module.
• Never expose the passenger air bag module to temperatures exceeding 90
°
C (194
°
F).
• Never allow oil, grease, detergent, or water to come in contact with the passenger air bag module.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Never use the old fixing bolts after removal; replace with the new bolts.
• Never damage the harness while installing.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT-III. Refer to
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
: Pawl
JMHIA0660ZZ
: Upward
JMHIA0661ZZ
JMHIA0009ZZ
SIDE CURTAIN AIR BAG MODULE
SR-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
SIDE CURTAIN AIR BAG MODULE
Exploded View
INFOID:0000000005249834
Removal and Installation
INFOID:0000000005249835
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
• Never use the air tools or the electric tools for servicing.
REMOVAL
1.
Remove the headlining. Refer to
INT-24, "Removal and Installation"
.
2.
Remove the side curtain air bag module harness connector.
CAUTION:
• For installing/removing the side curtain air bag module
harness connector, insert thin screwdriver wrapped in
tape into notch, lift lock and remove connector.
• Install the connector with lock raised, and push lock into
the connector.
• After installing the connector, check that the lock is
pushed securely into it.
3.
Remove the fixing bolts, and then remove the side curtain air bag module.
CAUTION:
1.
Side curtain air bag module
Refer to
JMHIA0662GB
PHIA0953J
SR-20
< REMOVAL AND INSTALLATION >
SIDE CURTAIN AIR BAG MODULE
• Never impact the side curtain air bag module.
• Replace the side curtain air bag module if it has been dropped
or sustained an impact.
• Never insert any foreign objects (screwdriver, etc.) into side curtain air bag module.
• Never disassemble the side curtain air bag module.
• Never expose the side curtain air bag module to temperatures exceeding 90
°
C (194
°
F).
• Never allow oil, grease, detergent, or water to come in contact with the side curtain air bag module.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Never damage the harness while installing.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT-III. Refer to
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
JMHIA0009ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст