Infiniti FX35, FX50 (S51). Manual — part 1872

P1815 M-MODE SWITCH

TM-295

< DTC/CIRCUIT DIAGNOSIS >

[7AT: RE7R01B (VK50VE)]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

Component Inspection [Paddle Shifter (Shift-down)]

INFOID:0000000005250302

1.

CHECK PADDLE SHIFTER (SHIFT-DOWN)

Check continuity between paddle shifter (shift-down) connector terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace paddle shifter (shift-down). Refer to

TM-354, "Exploded View"

.

Paddle shifter (shift-down) connector

Condition

Continuity

Connector

Terminal

M39

1

3

Paddle shifter (shift-down)
is pulled.

Existed

Other than the above

Not existed

TM-296

< DTC/CIRCUIT DIAGNOSIS >

[7AT: RE7R01B (VK50VE)]

P2713 PRESSURE CONTROL SOLENOID D

P2713 PRESSURE CONTROL SOLENOID D

Description

INFOID:0000000005250303

• The high and low reverse clutch solenoid valve is controlled by the TCM in response to signals transmitted

from the transmission range switch, output speed sensor and accelerator pedal position sensor. Gears will
then be shifted to the optimum position.

• The high and low reverse clutch solenoid valve controls the high and low reverse clutch control valve in

response to a signal transmitted from the TCM.

DTC Logic

INFOID:0000000005250304

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CAUTION:

Always drive vehicle at a safe speed.

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

With CONSULT-III

1.

Start the engine.

2.

Select “BATTERY VOLT”, “MANU MODE SW”, “GEAR” and “VHCL/S SE-A/T” in “Data Monitor” in
“TRANSMISSION”.

3.

Drive the vehicle and maintain the following conditions for 5 seconds or more.

4.

Perform “Self Diagnostic Results” in “TRANSMISSION”.

With GST

Follow the procedure “With CONSULT-III”.

Is “P2713” detected?

YES

>> Go to

TM-296, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000005250305

1.

CHECK INTERMITTENT INCIDENT

Refer to

GI-36, "Intermittent Incident"

.

Is the inspection result normal?

YES

>> Replace A/T assembly. Refer to

TM-362, "Exploded View"

.

NO

>> Repair or replace damaged parts.

DTC

Trouble diagnosis name

DTC is detected if...

Possible cause

P2713

Pressure Control Solenoid D

The high and low reverse clutch
solenoid valve monitor value is
0.4 A or less when the high and
low reverse clutch solenoid
valve command value is more
than 0.75 A.

• Harness or connectors

(Solenoid valve circuit is
open or shorted.)

• High and low reverse clutch

solenoid valve

BATTERY VOLT

: 9 V or more

MANU MODE SW

: ON

GEAR

: 3rd

VHCL/S SE-A/T

: 10 km/h (7 MPH) or more

P2722 PRESSURE CONTROL SOLENOID E

TM-297

< DTC/CIRCUIT DIAGNOSIS >

[7AT: RE7R01B (VK50VE)]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

P2722 PRESSURE CONTROL SOLENOID E

Description

INFOID:0000000005250306

• The low brake solenoid valve is controlled by the TCM in response to signals transmitted from the transmis-

sion range switch, output speed sensor and accelerator pedal position sensor. Gears will then be shifted to
the optimum position.

• The low brake solenoid valve controls the low brake control valve in response to a signal transmitted from

the TCM.

DTC Logic

INFOID:0000000005250307

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CAUTION:

Always drive vehicle at a safe speed.

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

With CONSULT-III

1.

Start the engine.

2.

Select “BATTERY VOLT”, “MANU MODE SW”, “GEAR” and “VHCL/S SE-A/T” in “Data Monitor” in
“TRANSMISSION”.

3.

Drive vehicle and maintain the following conditions for 5 seconds or more.

4.

Perform “Self Diagnostic Results” in “TRANSMISSION”.

With GST

Follow the procedure “With CONSULT-III”.
Is “P2722” detected?

YES

>> Go to

TM-297, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000005250308

1.

CHECK INTERMITTENT INCIDENT

Refer to

GI-36, "Intermittent Incident"

.

Is the inspection result normal?

YES

>> Replace A/T assembly. Refer to

TM-362, "Exploded View"

.

NO

>> Repair or replace damaged parts.

DTC

Trouble diagnosis name

DTC is detected if...

Possible cause

P2722

Pressure Control Solenoid E

The low brake solenoid valve
monitor value is 0.4 A or less
when the low brake solenoid
valve command value is more
than 0.75 A.

• Harness or connectors

(Solenoid valve circuit is
open or shorted.)

• Low brake solenoid valve

BATTERY VOLT

: 9 V or more

MANU MODE SW

: ON

GEAR

: 1st

VHCL/S SE-A/T

: 10 km/h (7 MPH) or more

TM-298

< DTC/CIRCUIT DIAGNOSIS >

[7AT: RE7R01B (VK50VE)]

P2731 PRESSURE CONTROL SOLENOID F

P2731 PRESSURE CONTROL SOLENOID F

Description

INFOID:0000000005250309

• The 2346 brake solenoid valve is controlled by the TCM in response to signals transmitted from the trans-

mission range switch, output speed sensor and accelerator pedal position sensor. Gears will then be shifted
to the optimum position.

• The 2346 brake solenoid valve controls the 2346 brake control valve in response to a signal transmitted from

the TCM.

DTC Logic

INFOID:0000000005250310

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CAUTION:

Always drive vehicle at a safe speed.

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

With CONSULT-III

1.

Start the engine.

2.

Select “BATTERY VOLT”, “MANU MODE SW”, “GEAR” and “VHCL/S SE-A/T” in “Data Monitor” in
“TRANSMISSION”.

3.

Drive vehicle and maintain the following conditions for 5 seconds or more.

4.

Perform “Self Diagnostic Results” in “TRANSMISSION”.

With GST

Follow the procedure “With CONSULT-III”.
Is “P2731” detected?

YES

>> Go to

TM-298, "Diagnosis Procedure"

.

NO

>> Check intermittent incident. Refer to

GI-36, "Intermittent Incident"

.

Diagnosis Procedure

INFOID:0000000005250311

1.

CHECK INTERMITTENT INCIDENT

Refer to

GI-36, "Intermittent Incident"

.

Is the inspection result normal?

YES

>> Replace A/T assembly. Refer to

TM-362, "Exploded View"

.

NO

>> Repair or replace damaged parts.

DTC

Trouble diagnosis name

DTC is detected if...

Possible cause

P2731

Pressure Control Solenoid F

The 2346 brake solenoid valve
monitor value is 0.4 A or less
when the 2346 brake solenoid
valve command value is more
than 0.75 A.

• Harness or connectors

(Solenoid valve circuit is
open or shorted.)

• 2346 brake solenoid valve

BATTERY VOLT

: 9 V or more

MANU MODE SW

: ON

GEAR

: 2nd

VHCL/S SE-A/T

: 10 km/h (7 MPH) or more