Infiniti FX35, FX50 (S51). Manual — part 612
DIFFERENTIAL ASSEMBLY
DLN-283
< UNIT DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: R230]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
Adjust the pinion bearing preload first, then adjust the side bearing preload.
SIDE BEARING PRELOAD
Before inspection and adjustment, drain gear oil.
1.
Remove rear cover. Refer to
.
2.
Make sure all parts are clean. Also, make sure the bearings are
well lubricated with gear oil.
3.
Place the differential case, with side bearings and bearing races
installed, into gear carrier.
4.
Insert left and right original side bearing adjusting washers in
place between side bearings and gear carrier.
5.
Install bearing caps in their correct locations and tighten bearing
cap mounting bolts.
6.
Turn the carrier several times to seat the bearings.
7.
Measure the turning torque of the carrier at the drive gear mounting bolts with a spring gauge [SST:
—
(J-8129)].
When the preload torque is large
On pinion bearings:
Replace the collapsible spacer.
On side bearings:
Use thinner side bearing adjusting washers by the same amount to
each side.
When the preload is small
On pinion bearings:
Tighten the drive pinion lock nut.
On side bearings:
Use thicker side bearing adjusting washers by the same amount to
each side.
SPD527
SPD558
SDIA1795E
Standard
Specification
: Refer to
DLN-284
< UNIT DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: R230]
DIFFERENTIAL ASSEMBLY
8.
If the turning torque is outside the specification, use a thicker/
thinner side bearing adjusting washer to adjust.
CAUTION:
Select a side bearing adjusting washer for right and left
individually.
9.
Record the total amount of washer thickness required for the correct carrier side bearing preload.
DRIVE GEAR RUNOUT
1.
Remove rear cover. Refer to
.
2.
Fit a dial indicator to the drive gear back face.
3.
Rotate the drive gear to measure runout.
• If the runout is outside of the repair limit, check drive gear
assembly condition; foreign material may be caught between
drive gear and differential case, or differential case or drive
gear may be deformed, etc.
CAUTION:
Replace drive gear and drive pinion gear as a set.
TOOTH CONTACT
Before inspection and adjustment, drain gear oil.
1.
Remove rear cover. Refer to
.
2.
Apply red lead to drive gear.
CAUTION:
Apply red lead to both the faces of 3 to 4 gears at 4 loca-
tions evenly spaced on drive gear.
3.
Rotate drive gear back and forth several times, check drive pin-
ion gear to drive gear tooth contact.
CAUTION:
Check tooth contact on drive side and reverse side.
If the turning torque is less
than the specified range:
Use a thicker thrust wash-
er.
If the turning torque is
greater than the specifica-
tion:
Use a thinner thrust wash-
er.
SPD772
Limit
Drive gear runout
: Refer to
SPD886
SPD357
SDIA0570E
DIFFERENTIAL ASSEMBLY
DLN-285
< UNIT DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: R230]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
4.
If tooth contact is improperly adjusted, follow the procedure
below to adjust the pinion height [dimension (X)].
• If the tooth contact is near the face (face contact), or near the
heel (heel contact), thicken pinion height adjusting washers to
move drive pinion closer to drive gear.
SDIA0207E
SDIA0517E
PDIA0440E
DLN-286
< UNIT DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: R230]
DIFFERENTIAL ASSEMBLY
• If the tooth contact is near the flank (flank contact), or near the
toe (toe contact), thin pinion height adjusting washers to move
drive pinion farther from drive gear.
BACKLASH
Before inspection and adjustment, drain gear oil.
1.
Remove rear cover. Refer to
.
2.
Fit a dial indicator to the drive gear face to measure the back-
lash.
• If the backlash is outside of the specified value, change the
thickness of side bearing adjusting washer.
CAUTION:
Never change the total amount of washers as it changes the bearing preload.
Inspection After Disassembly
INFOID:0000000005249282
DRIVE GEAR AND DRIVE PINION
• Clean up the disassembled parts.
• If the gear teeth never mesh or line-up correctly, determine the cause and adjust or replace as necessary.
• If the gears are worn, cracked, damaged, pitted or chipped (by friction) noticeably, replace with new drive
gear and drive pinion as a set.
BEARING
• Clean up the disassembled parts.
• If any chipped (by friction), pitted, worn, rusted or scratched marks, or unusual noise from the bearing is
observed, replace as a bearing assembly (as a new set).
SIDE GEAR AND PINION MATE GEAR
• Clean up the disassembled parts.
• If any cracks or damage on the surface of the tooth is found, replace.
• If any worn or chipped mark on the contact sides of the thrust washer is found, replace.
SIDE GEAR THRUST WASHER AND PINION MATE THRUST WASHER
• Clean up the disassembled parts.
• If it is chipped (by friction), damaged, or unusually worn, replace.
OIL SEAL
• Whenever disassembled, replace.
PDIA0441E
Standard
Backlash
: Refer to
.
When the backlash is large:
Make drive gear back side adjusting washer thicker,
and drive gear tooth side adjusting washer thinner by
the same amount.
When the backlash is small:
Make drive gear back side adjusting washer thinner,
and drive gear tooth side adjusting washer thicker by
the same amount.
SPD513
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст