Infiniti F50. Manual — part 479
DTC P1448 EVAP CANISTER VENT CONTROL VALVE
EC-557
C
D
E
F
G
H
I
J
K
L
M
A
EC
4.
CHECK IF EVAP CANISTER SATURATED WITH WATER
1.
Remove EVAP canister with EVAP canister vent control valve attached.
2.
Check if water will drain from the EVAP canister.
Yes or No
Yes
>> GO TO 5.
No
>> GO TO 7.
5.
CHECK EVAP CANISTER
Weigh the EVAP canister with the EVAP canister vent control valve attached.
The weight should be less than 1.8 kg (4.0 lb).
OK or NG
OK
>> GO TO 7.
NG
>> GO TO 6.
6.
DETECT MALFUNCTIONING PART
Check the following.
●
EVAP canister for damage
●
EVAP hose between EVAP canister and water separator for clogging or poor connection
>> Repair hose or replace EVAP canister.
7.
CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR HOSE
Check disconnection or improper connection of hose connected to EVAP control system pressure sensor.
OK or NG
OK
>> GO TO 8.
NG
>> Repair it.
8.
CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR CONNECTOR
1.
Disconnect EVAP control system pressure sensor harness connector.
2.
Check connectors for water.
OK or NG
OK
>> GO TO 9.
NG
>> Replace EVAP control system pressure sensor.
9.
CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR
Refer to
EC-365, "Component Inspection"
OK or NG
OK
>> GO TO 10.
NG
>> Replace EVAP control system pressure sensor.
SEF596U
Water should not exist.
EC-558
DTC P1448 EVAP CANISTER VENT CONTROL VALVE
10.
CHECK INTERMITTENT INCIDENT
Refer to
EC-132, "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT"
.
>> INSPECTION END
Component Inspection
EBS00ML8
EVAP CANISTER VENT CONTROL VALVE
With CONSULT-II
1.
Remove EVAP canister vent control valve from EVAP canister.
2.
Check portion B of EVAP canister vent control valve for being
rusted.
3.
Reconnect harness connectors disconnected.
4.
Turn ignition switch “ON”.
5.
Perform “VENT CONTROL/V” in “ACTIVE TEST” mode.
6.
Check air passage continuity and operation delay time.
7.
Clean the air passage (Portion A to B ) of EVAP canister vent
control valve using an air blower.
8.
Perform Test No. 9 again.
With GST
1.
Remove EVAP canister vent control valve from EVAP canister.
2.
Check portion B of EVAP canister vent control valve for being
rusted.
3.
Check air passage continuity and operation delay time under the
following conditions.
Make sure new O-ring is installed properly.
4.
Clean the air passage (Portion A to B ) of EVAP canister vent
control valve using an air blower.
5.
Perform Test No. 9 again.
SEF337X
PBIB0153E
SEF337X
PBIB0154E
DTC P1456 EVAP CONTROL SYSTEM
EC-559
C
D
E
F
G
H
I
J
K
L
M
A
EC
DTC P1456 EVAP CONTROL SYSTEM
PFP:14710
On Board Diagnosis Logic
EBS00ML9
This diagnosis detects very small leaks in the EVAP line between fuel tank and EVAP canister purge volume
control solenoid valve, using vapor pressure in the fuel tank in the same way as conventional EVAP small leak
diagnosis.
If ECM judges a leak which corresponds to a very small leak, the very small leak P0456 will be detected.
If ECM judges a leak equivalent to a small leak, EVAP small leak P1442 will be detected.
If ECM judges there are no leaks, the diagnosis will be OK.
CAUTION:
●
Use only a genuine NISSAN fuel filler cap as a replacement. If an incorrect fuel filler cap is used,
the MIL may come on.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0456
0456
Evaporative emission
control system very
small leak (negative
pressure check)
●
EVAP system has a very small leak.
●
EVAP system does not operate prop-
erly.
●
Incorrect fuel tank vacuum relief valve
●
Incorrect fuel filler cap used
●
Fuel filler cap remains open or fails to close.
●
Foreign matter caught in fuel filler cap.
●
Leak is in line between intake manifold and EVAP
canister purge volume control solenoid valve.
●
Foreign matter caught in EVAP canister vent con-
trol valve.
●
EVAP canister or fuel tank leaks
●
EVAP purge line (pipe and rubber tube) leaks
●
EVAP purge line rubber tube bent
●
Blocked or bent rubber tube to EVAP control sys-
tem pressure sensor
●
Loose or disconnected rubber tube
●
EVAP canister vent control valve and the circuit
●
EVAP canister purge volume control solenoid
valve and the circuit
●
Absolute pressure sensor
●
Fuel tank temperature sensor
●
O-ring of EVAP canister vent control valve is miss-
ing or damaged
●
Water separator
●
EVAP canister is saturated with water
●
EVAP control system pressure sensor
●
Refueling control valve
●
ORVR system leaks
●
Fuel level sensor and the circuit
●
Foreign matter caught in EVAP canister purge vol-
ume control solenoid valve
SEF323U
EC-560
DTC P1456 EVAP CONTROL SYSTEM
●
If the fuel filler cap is not tightened properly, the MIL may come on.
●
Use only a genuine NISSAN rubber tube as a replacement.
DTC Confirmation Procedure
EBS00MLA
NOTE:
●
If DTC P1456 is displayed with P1442, perform TROUBLE DIAGNOSIS FOR DTC P1456 first.
●
After repair, make sure that the hoses and clips are installed properly.
●
If “DTC Confirmation Procedure” has been previously conducted, always turn ignition switch “OFF” and
wait at least 10 seconds before conducting the next test.
TESTING CONDITION:
●
Open engine hood before conducting following procedure.
●
If any of following conditions are met just before the DTC confirmation procedure, leave the vehi-
cle for more than 1 hour.
–
Fuel filler cap is removed.
–
Refilled or drained the fuel.
–
EVAP component parts is/are removed.
●
Before performing the following procedure, confirm that battery voltage is more than 11V at idle.
WITH CONSULT-II
1.
Turn ignition switch “ON” and select “DATA MONITOR” mode with CONSULT-II.
2.
Make sure the following conditions are met.
FUEL LEVEL SE: 0.25 - 1.15V
COOLAN TEMP/S: 0 - 32
°
C (32 - 90
°
F)
FUEL T/TMP SE: 0 - 35
°
C (32 - 95
°
F)
INT A/TEMP SE: More than 0
°
C (32
°
F)
If NG, turn ignition switch “OFF” and leave the vehicle in a cool
place (soak the vehicle) or refilling/draining fuel until the output
voltage condition of the “FUEL LEVEL SE” meets within the
range above and leave the vehicle for more than 1 hour. Then
start from step 1).
3.
Turn ignition switch “OFF” and wait at least 10 seconds.
4.
Turn ignition switch “ON”.
5.
Select “EVAP V/S LEAK P0456/P1456” of “EVAPORATIVE
SYSTEM” in “DTC WORK SUPPORT” mode with CONSULT-II.
Follow the instruction displayed.
6.
Make sure that “OK” is displayed.
If “NG” is displayed, refer to
EC-562, "Diagnostic Procedure"
NOTE:
●
If the engine speed cannot be maintained within the range displayed on CONSULT-II screen, go
to
.
●
Make sure that EVAP hoses are connected to EVAP canister purge volume control solenoid
valve properly.
PBIB1953E
PBIB0837E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст