Infiniti F50. Manual — part 524
BODY SIDE TRIM
EI-37
C
D
E
F
G
H
J
K
L
M
A
B
EI
BODY SIDE TRIM
PFP:76913
Removal and Installation
EIS000DL
CAUTION:
●
Wrap the tip of flat-bladed screwdriver with a cloth when removing metal clips from garnishes.
●
When removing or installing body side welts, do not allow butyl seal to come in contact with pillar
garnish.
1.
Front pillar garnish
2.
Dash side finisher
3.
Front body side welt
4.
Front kicking plate
5.
Center pillar garnish
6.
Center pillar lower garnish
7.
Rear body side welt
8.
Rear kicking plate
9.
Rear pillar finisher
10.
Rear wheel house garnish
11.
Rear cooler inlet grille
12.
Rear cooler outlet grille
13.
Center pillar upper cap
14.
Rear pillar upper cap
15.
Mudguard finisher (front)
16.
Mudguard finisher (rear)
SIIA0814E
EI-38
BODY SIDE TRIM
CENTER PILLAR LOWER GARNISH
Removal
1.
Remove front and rear kicking plate.
2.
Remove rear cooler inlet grille
Installation
Install in the reverse order of removal.
CENTER PILLAR UPPER GARNISH
Removal
1.
Remove seat belt shoulder anchor. Refer to
SB-3, "Removal and Installation of Front Seat Belt"
2.
Remove front and rear kicking plate.
3.
Remove center pillar lower garnish.
Installation
To install, reverse the removal procedure sequence.
REAR PILLAR FINISHER
Removal
1.
Remove rear seat. Refer to
SE-197, "Removal and Installation"
2.
Remove rear kicking plate.
3.
Remove rear wheel house garnish.
Installation
Install in the reverse order of removal.
DASH SIDE FINISHER
Removal
1.
Remove front kicking plate.
2.
Remove front body side welt.
CAUTION:
Insert screw driver rolled with cloth between panel on vehicle
and clips (as indicated with arrow), and disconnect clips.
Installation
Install in the reverse order of removal.
CAUTION:
To install, check if all clips are matched over holes of panel on vehicle, then push on.
SIIA0810E
REAR PARCEL SHELF FINISHER
EI-39
C
D
E
F
G
H
J
K
L
M
A
B
EI
REAR PARCEL SHELF FINISHER
PFP:79910
Removal and Installation
EIS000DM
REMOVAL
1.
Remove rear seat. Refer to
SE-197, "Removal and Installation"
2.
Remove rear seat belt floor anchor bolts. Refer to
SE-197, "Removal and Installation"
.
3.
Remove rear pillar finisher. Refer to
SE-197, "Removal and Installation"
SIIA0815E
1.
Rear parcel shelf finisher
2.
Seat belt escutcheon
3.
High mounted stop lamp
4.
Woofer grille
5.
Rear sunshade
6.
Top tether strap child restraint
cover
EI-40
REAR PARCEL SHELF FINISHER
4.
Remove high-mounted stop lamp, and disconnect connectors.
5.
Remove woofer grille.
6.
Remove seat belt escutcheon.
7.
Remove clips, and remove rear parcel shelf finisher.
8.
Disconnect rear sunshade connectors, remove screws, and remove rear sunshade.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
●
Confirm hooks of rear parcel shelf finisher are completely inserted into holes on vehicle side.
●
Confirm clips are matched over holes on vehicle side, then push on.
SIIA0820E
SIIA0821E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст