Infiniti F50. Manual — part 214
DOOR
BL-103
C
D
E
F
G
H
J
K
L
M
A
B
BL
2.
Adjust the striker so that it becomes parallel with the lock inser-
tion direction.
Removal and Installation of Front Door
EIS000HB
CAUTION:
●
When removing and installing the door assembly, support the door with a jack and cloth to protect
the door and body.
●
When removing and installing door assembly, be sure to carry out the fitting adjustment.
●
Check the hinge rotating part for poor lubrication. If necessary, apply “body grease”.
●
After installing, check operation.
REMOVAL
1.
Pull the lever and remove the front door harness connector
while removing tabs of door harness connector.
2.
Remove the check link cover.
3.
Remove the mounting bolts of the check link on the vehicle.
4.
Remove the door-side hinge mounting nuts and bolts, and
remove the door assembly.
SIIA0338E
PIIA2514E
SIIA0339E
PIIA3473E
BL-104
DOOR
INSTALLATION
Install in the reverse order of removal.
Removal and Installation of Rear Door
EIS003PQ
CAUTION:
●
When removing and installing the rear door assembly, support the door with a jack and cloth to
protect the door and body.
●
When removing and installing rear door assembly, be sure to carry out the fitting adjustment.
●
Check the hinge rotating part for poor lubrication. If necessary, apply “body grease”.
●
After installing, check operation.
REMOVAL
1.
Grommet is pulled out, and the Rear door harness connector is
detached.
2.
Remove the check link cover.
3.
Remove the mounting bolts of the check link on the vehicle.
4.
Remove the door-side hinge mounting nuts, and remove the
door assembly.
INSTALLATION
Install in the reverse order of assembly.
PIIA3412E
PIIA2788E
PIIA3431E
DOOR
BL-105
C
D
E
F
G
H
J
K
L
M
A
B
BL
Door Weatherstrip
EIS000HC
SIIA0328E
BL-106
FRONT DOOR LOCK
FRONT DOOR LOCK
PFP:80502
Component Structure
EIS000HD
Inspection and Adjustment
EIS000HE
1.
Remove the front door finisher. Refer to
EI-30, "Removal and Installation"
.
2.
Remove the front speaker. Refer to
AV-36, "Removal and Installation of Door Speaker"
3.
Remove the front door window. Refer to
GW-51, "Removal and Installation"
.
4.
Remove the front door module assembly. Refer to
GW-51, "Removal and Installation"
EXTERIOR HANDLE ROD ADJUSTMENT
Rotate the bushing to adjust so that the clearance between the bush-
ing and rod becomes as shown in the figure.
CAUTION:
Be careful not to make the clearance 0 mm (0 in) or the rod
pressed continuously.
Removal and Installation
EIS000HF
REMOVAL
1.
Remove the front door finisher. Refer to
EI-30, "Removal and Installation"
.
2.
Remove the front speaker. Refer to
AV-36, "Removal and Installation of Door Speaker"
3.
Remove the front door window.
GW-51, "Removal and Installation"
.
4.
Remove the front door module assembly.
GW-51, "Removal and Installation"
1.
Outside handle
2.
Key cylinder (Driver side only)
3.
Outside handle rod
4.
Key lock rod
5.
Door lock assembly
6.
Door lock actuator
7.
Inside handle cable
8.
Inside handle
9.
Lock knob cable
10. Lock knob
PIIA3475E
SBT978
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст