Infiniti F50. Manual — part 213
REMOTE KEYLESS ENTRY SYSTEM
BL-99
C
D
E
F
G
H
J
K
L
M
A
B
BL
ID Code Entry Procedure
EIS003OR
PROCEDURE 1 (WITHOUT CONSULT-II)
PIIA4474E
BL-100
REMOTE KEYLESS ENTRY SYSTEM
NOTE:
●
If a electronic key is lost, the ID code of the lost electronic key must be erased to prevent unauthorized
use. A specific ID code can be erased with CONSULT-II. However, when the ID code of a lost electronic
key is not known, all controller ID codes should be erased. After all ID codes are erased, the ID codes of
all remaining and/or new remote controllers must be re-registered. To erase all ID codes in memory, regis-
ter one ID code (electronic key) four times. After all ID codes are erased, the ID codes of all remaining
and/or new electronic keys must be re-registered.
●
When registering an additional electronic key, the existing ID codes in memory may or may not be erased.
If four ID codes are stored in memory, when an additional code is registered, only the oldest code is
erased. If less than four ID codes are stored in memory, when an additional ID code is registered, the new
ID code is added and no ID codes are erased.
●
If you need to activate more than two additional new electronic keys, repeat the procedure “Additional ID
code entry” for each new electronic key.
●
Entry of maximum four ID codes is allowed. When more than four ID codes are entered, the oldest ID
code will be erased.
●
Even if same ID code that is already in the memory is input, the same ID code can be entered. The code
is counted as an additional code.
PROCEDURE 2 (WITH CONSULT-II)
NOTE:
If a electronic key is lost, the ID code of the lost electronic key must be erased to prevent unauthorized use.
When the ID code of a lost electronic key is not known, all controller ID codes should be erased. After all ID
codes are erased, the ID codes of all remaining and/or new remote controllers must be re-registered.
1.
Turn ignition switch “OFF”.
2.
Connect “CONSULT-ll” and “CONSULT-ll CONVERTER” to the
data link connector.
3.
Turn ignition switch “ON”.
4.
Touch “START (NISSAN BASED VHCL)”
5.
Touch “IVMS”
If “IVMS” is not indicated, go to
PBIB0196E
MBIB0233E
PIIA0183E
REMOTE KEYLESS ENTRY SYSTEM
BL-101
C
D
E
F
G
H
J
K
L
M
A
B
BL
6.
Check the model specification, touch either “WITH SUNROOF”
or “WITHOUT SUNROOF”.
7.
Touch “OK”. If the selection is wrong, touch “CANCEL”.
8.
Touch “MULTI-REMOTE CONT SYS”.
9.
Touch “WORK SUPPORT”.
10. The item shown on the figure at right can be set up.
●
“REMO CONT ID CONFIR”
Use this mode to confirm if a electronic key ID code is registered
or not.
●
“REMO CONT ID REG” Use this mode to register a electronic
key ID code.
NOTE:
Register the ID code when electronic key or BCM is replaced, or
when additional electronic key is required.
●
“REMO CONT ID ERASUR” Use this mode to erase a electronic
key ID code.
Removal and Installation of Remote Keyless Entry Receiver
EIS003SP
REMOVE
1.
Remove the rear parcel shelf finisher. Refer to
EI-39, "Removal and Installation"
2.
Disconnect the remote keyless entry receiver connector, mount-
ing screw and remove the remote keyless entry receiver.
INSTALLATION
Install in the reverse order of removal.
PIIA0184E
PIIA0373E
SEL274W
PIIA3445E
BL-102
DOOR
DOOR
PFP:80100
Fitting Adjustment
EIS000HA
FRONT DOOR
Longitudinal Clearance and Surface Height Adjustment at Front End
1.
Accessing from inside the fender, loosen the hinge mounting bolts. Raise the front door at rear end to
adjust.
REAR DOOR
Longitudinal Clearance and Surface Height Adjustment at Front End
1.
Remove the center pillar upper garnish and center pillar lower garnish. Refer to
2.
Accessing from inside the vehicle, loosen the mounting nuts. Open the rear door, and raise the rear door
at rear end to adjust.
STRIKER ADJUSTMENT
1.
Remove the striker cover.
PIIA3411E
SIIA0886E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст