Infiniti F50. Manual — part 308
WARNING CHIME
DI-75
C
D
E
F
G
H
I
J
L
M
A
B
DI
4.
CHECK SEAT BELT BUCKLE SWITCH GROUND CIRCUIT
Check continuity between seat belt buckle connector B150 terminal
15A (B) and ground.
OK or NG
OK
>> System is OK (Inspection end)
NG
>> Repair harness or connector.
Removal and Installation of Warning Chime
EKS00119
REMOVAL
1.
Remove the cluster lid C, refer to
.
2.
Remove bolt (1), and remove warning chime.
INSTALLATION
Install in the reverse order of removal.
15A – Ground
: continuity
SKIA4104E
SKIA0582E
DI-76
VEHICLE INFORMATION AND INTEGRATED SWITCH SYSTEM /WITHOUT
NAVIGATION SYSTEM
VEHICLE INFORMATION AND INTEGRATED SWITCH SYSTEM /WITHOUT NAVI-
GATION SYSTEM
PFP:28395
System Description
EKS007A9
INTEGRATED SWITCH SYSTEM
Using the multifunction switch at the center of the instrument panel, the controls of the following systems are
centralized:
●
Auto A/C system
●
Vehicle information system
●
Audio system
●
Hazard switch
The multifunction switch can operate and check the vehicle condition and each setting (vehicle electrical sys-
tem).
PRECAUTION OF LCD MONITOR
●
When passenger compartment temperature is low, the LCD monitor sometimes dims because of the
brightness of the back light (small fluorescent light) integrated into the LCD monitor decrease. In this case,
the refreshing rate of the picture also becomes low because of the low response of the LCD monitor.
When passenger compartment becomes warm, however, the LCD recovers the normal display.
●
Sometimes, black or bright dots peculiar to LCD monitor can be seen on the display.
●
Back light sometimes flickers or darkens according to the total consumption hours and the number of ON
and OFF switching. In this case, the back light should be replaced. (LCD monitor assembly)
POWER SUPPLY AND GROUND
Power Is Supplied At All Times
●
through 15 A fuse [No. 52, located in fuse, fusible link and relay box (J/B)]
●
to AV control unit terminals 2 and 3, and
●
to display terminals 21 and 23.
When Ignition Switch is in ACC or ON Position, Power is Supplied
●
through 10 A fuse [No. 21, located in fuse block (J/B) No. 1]
●
to AV control unit terminal 6, and
●
to display terminal 19, and
●
to multifunction switch terminal 1.
When Ignition Switch is in ON or START Position, Power is Supplied
●
through 10 A fuse [No. 1, located in fuse block (J/B) No. 1]
●
to AV control unit terminal 27.
Ground is Supplied
●
to AV control unit terminal 1and 4
●
through body grounds M25 and M115, and
●
to multifunction switch terminal 2 and
●
to display terminals 22 and 24
●
through grounds M24 and M114.
AV COMMUNICATION LINE
AV control unit is connected to the following units by AV communication line. Each unit transmits/receives data
with AV communication line.
●
Display
●
Multifunction switch
●
Audio unit
●
BOSE speaker amp. (audio amp.)
●
Rear view camera control unit
●
Low tire pressure warning control unit
VEHICLE INFORMATION AND INTEGRATED SWITCH SYSTEM /WITHOUT
NAVIGATION SYSTEM
DI-77
C
D
E
F
G
H
I
J
L
M
A
B
DI
●
Voice activated control module
VEHICLE INFORMATION SYSTEM
●
AV control unit is received vehicle information system of signals from combination meter.
●
AV control unit is communicating with BCM and combination meter.
1.
Press “INFO” switch to display vehicle information display.
2.
Select “Trip Computer”, “Fuel Economy”, “Maintenance” or“Tire
Pressure”.
*: Maintenance information displays the change cycle of engine oil, oil filter and tire on LCD monitor depending on the driving dis-
tance specified by a driver or a technician.
SKIA0600E
SKIA0599E
Display items
Display/Setting contents
Trip Computer
Elapsed time
Driving distance
Average speed
Fuel Economy
Average fuel economy (MPG)
Distance to empty (Miles)
Fuel economy (MPG)
Fuel economy record
Maintenance
(with Maintenance information*)
Maintenance intervals of engine oil and setting of oil change cycle
Maintenance intervals of oil filter and setting of filter replacement cycle
Maintenance intervals of tire and setting of tire replacement cycle
Tire Pressure
Tire pressure information
DI-78
VEHICLE INFORMATION AND INTEGRATED SWITCH SYSTEM /WITHOUT
NAVIGATION SYSTEM
Trip Computer Information
1.
Select “Trip Computer”.
2.
Elapsed Time, Driving Distance and Average Speed are dis-
played as Trip Computer information.
Fuel Economy Information
1.
Select “Fuel Economy”.
2.
Average Fuel Economy, Distance to Empty, Fuel Economy are
displayed as Fuel Economy information.
3.
Select “Fuel Economy Record”. The average fuel consumption
history will be displayed in graph along with the average for the
previous Reset – to – Reset period.
Maintenance Information
1.
Select “Maintenance”.
2.
Engine Oil, Oil Filter and Tire Rotation are displayed as Mainte-
nance information.
SKIA0601E
SKIA0602E
SKIA0603E
SKIA0604E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст