Infiniti QX56 (Z62). Manual — part 371
DAS
BSW SYSTEM SYMPTOMS
DAS-521
< SYMPTOM DIAGNOSIS >
[BSW]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
SYMPTOM DIAGNOSIS
BSW SYSTEM SYMPTOMS
Symptom Table
INFOID:0000000006223979
CAUTION:
Perform the self-diagnosis with CONSULT-III before the symptom diagnosis. Perform the trouble diag-
nosis if any DTC is detected.
NOTE:
For the operational conditions of BSW, refer to
.
Symptom
Possible cause
Inspection item/Reference page
Indicator/warning lamps do not il-
luminate when ignition switch
OFF
⇒
ON.
BSW warning lamp (Yellow)
does not illuminate
• BSW warning lamp signal
(CAN)
- Combination meter
- ADAS control unit
• BSW warning lamp (combina-
tion meter)
• ADAS control unit Active test
“BSW/BSI WARNING LAMP”
Refer to
SULT-III Function (ICC/
ADAS)"
• ADAS control unit Data moni-
tor “BSW/BSI WARN LMP”
Refer to
SULT-III Function (ICC/
ADAS)"
• Combination meter Data mon-
All of indicator/warning
lamps do not illuminate;
• BSW warning lamp
• Warning systems ON indi-
cator
• Power supply and ground cir-
cuit of ADAS control unit
• ADAS control unit
• Combination meter
Power supply and ground circuit
of ADAS control unit
Refer to
TROL UNIT : Diagnosis Proce-
dure"
Warning systems ON indica-
tor (on the warning systems
switch) does not illuminate
• Harness between ADAS con-
trol unit and warning systems
switch
• Warning systems switch
• ADAS control unit
Warning systems ON indicator
circuit
Refer to
BSW indicator does not turn
ON
• Harness between side radar
and BSW indicator
• Side radar LH/RH
• BSW indicator
Perform self-diagnosis of side ra-
dar
Refer to
BSW system is not activated.
(Indicator/warning lamps illumi-
nate when ignition switch OFF
⇒
ON.)
Warning systems ON indica-
tor is not turned ON
⇔
OFF
when operating warning sys-
tems switch
• Harness between ADAS con-
trol unit and waning systems
switch
• Harness between warning
systems switch and ground
• ADAS control unit
• Warning systems switch
Warning systems ON indicator
circuit
Refer to
Buzzer is not sounding
• Buzzer power supply circuit
• Harness between ADAS con-
trol unit and warning buzzer
• Harness between warning
buzzer and ground
• Warning buzzer
• ADAS control unit
Warning buzzer circuit
Refer to
DAS-522
< SYMPTOM DIAGNOSIS >
[BSW]
NORMAL OPERATING CONDITION
NORMAL OPERATING CONDITION
Description
INFOID:0000000006223980
PRECAUTIONS FOR BLIND SPOT WARNING (BSW)
• The BSW system is not a replacement for proper driving procedure and are not designed to prevent contact
with vehicles or objects. When changing lanes, always use the side and rear mirrors and turn and look in the
direction driver will move to ensure it is safe to change lanes. Never rely solely on the BSW system.
• The BSW system may not provide a warning for vehicles that pass through the detection zone quickly.
• Do not use the BSW system when towing a trailer because the system may not function properly.
• Excessive noise (e.g. audio system volume, open vehicle window) will interfere with the chime sound, and it
may not be heard.
• The side radar may not be able to detect and activate BSW when certain objects are present such as:
- Pedestrians, bicycles, animals.
- Several types of vehicles such as motorcycles.
- Oncoming vehicles.
- Vehicles remaining in the detection zone when driver accelerate from a stop.
- A vehicle merging into an adjacent lane at a speed approximately the same as vehicle.
- A vehicle approaching rapidly from behind.
- A vehicle which vehicle overtakes rapidly.
• Severe weather or road spray conditions may reduce the ability of the side radar to detect other vehicles.
• The side radar detection zone is designed based on a standard lane width. When driving in a wider lane, the
side radar may not detect vehicles in an adjacent lane. When driving in a narrow lane, the side radar may
detect vehicles driving two lanes away.
• The side radar are designed to ignore most stationary objects, however objects such as guardrails, walls,
foliage and parked vehicles may occasionally be detected. This is a normal operating condition.
DAS
SIDE RADAR
DAS-523
< REMOVAL AND INSTALLATION >
[BSW]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
REMOVAL AND INSTALLATION
SIDE RADAR
Removal and Installation
INFOID:0000000006223981
EXPLODED VIEW
REMOVAL AND INSTALLATION
Removal
1.
Remove the side radar RH/LH together with bracket.
2.
Remove the side radar connector.
NOTE:
This illustration is an example.
3.
Remove the mounting nuts to remove the side radar RH/LH from bracket.
Installation
Note the following, and install in the reverse order of removal.
1.
Bracket
2.
Bracket
3.
Side radar LH
4.
Bracket
5.
Side radar RH
6.
Bracket
A.
LH side
B.
RH side
Refer to
for symbol makes in the figure.
JSOIA0379GB
JSOIA0280ZZ
DAS-524
< REMOVAL AND INSTALLATION >
[BSW]
SIDE RADAR
• Tighten mounting nuts in the numerical order as shown in the fig-
ure.
• Always lock the side radar connector.
CAUTION:
• After replacing the side radar, activate (normal usage mode) it
in work support mode. Refer to
.
JSOIA0359ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст