Infiniti QX56 (Z62). Manual — part 445
DLK-246
< REMOVAL AND INSTALLATION >
BACK DOOR LOCK
BACK DOOR LOCK
Exploded View
INFOID:0000000006226105
DOOR LOCK
DOOR LOCK : Removal and Installation
INFOID:0000000006226106
REMOVAL
1.
Remove back door finisher lower. Refer to
INT-39, "Removal and Installation"
.
2.
Disconnect back door lock assembly harness connector.
3.
Remove back door lock mounting bolts, and then remove back door lock assembly.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
Check back door open/close, lock/unlock operation after installation.
TOUCH SENSOR
TOUCH SENSOR : Removal and Installation
INFOID:0000000006226107
CAUTION:
Take care not to bend touch sensor.
REMOVAL
1.
Remove back door finisher side. Refer to
INT-39, "Removal and Installation"
2.
Disconnect touch sensor connector.
1.
Back door support rod
2.
Touch sensor
3.
Automatic back door control module
4.
Back door lock assembly
5.
Back door assembly
6.
Stud ball
7.
Screw grommet
Refer to
for symbols in the figure.
JMKIA5484GB
BACK DOOR LOCK
DLK-247
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3.
Remove clips and TORX screws of touch sensor.
4.
Pull harness of touch sensor out of back door and remove touch sensor.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
Check back door open/close operation after installation.
BACK DOOR SUPPORT ROD
BACK DOOR SUPPORT ROD : Removal and Installation
INFOID:0000000006226108
REMOVAL
1.
Remove cap of back door finisher side (LH). Refer to
.
2.
Remove stud ball (1) of back door support rod (3) from back
door assembly (2).
3.
Remove automatic back door control module. Refer to
DLK-262, "Removal and Installation"
NOTE:
When replacing back door support rod, replace stud ball and automatic back door control module as a set,
since back door support rod is engaged and connected to stud ball and automatic back door control mod-
ule.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• When reusing stud ball, always apply locking sealant before installing stud ball to back door.
• Check back door open/close operation after installation.
EMERGENCY LEVER
EMERGENCY LEVER : Unlock procedures
INFOID:0000000006226109
UNLOCK PROCEDURES
NOTE:
If back door lock cannot be unlocked due to a malfunction or battery discharge, follow the procedures to
unlock back door.
1.
Remove the emergency handle mask. Refer to
.
2.
From inside the vehicle, rotate emergency lever toward lower
direction and unlock.
JMKIA5442ZZ
JMKIA5264ZZ
DLK-248
< REMOVAL AND INSTALLATION >
FUEL FILLER LID OPENER
FUEL FILLER LID OPENER
Exploded View
INFOID:0000000006226110
Removal and Installation
INFOID:0000000006226111
NOTE:
When fuel filler lid lock actuator (1) is a defective operation, pull the
rod to open fuel filler lid.
REMOVAL
1.
Fuel filler spring
2.
TORX bolt
3.
Fuel filler lid assembly
4.
Fuel lid bumper rubber
5.
Lock nut
6.
Lock & rod assembly
7.
Fuel filler lid lock actuator
: Pawl
: Vehicle front
JMKIA5269ZZ
JMKIA1960ZZ
FUEL FILLER LID OPENER
DLK-249
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
1.
Remove fuel mounting pin (1).
2.
Remove mounting TORX bolts, and then remove fuel filler lid.
3.
Remove luggage side lower finisher LH. Refer to
INT-36, "LUGGAGE SIDE LOWER FINISHER :
.
4.
Disconnect woofer connector.
5.
Remove woofer mounting bolts, and then remove woofer.
6.
Rotate lock nut counterclockwise, and then remove lock nut.
7.
Push fuel filler lid lock actuator behind the vehicle, while pushing the pawl.
8.
Disconnect harness connector and remove fuel filler lid lock actuator.
9.
Pull and remove lock & rod assembly forward, while pushing the pawls.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• After installation, check fuel filler lid assembly open/close, lock/unlock operation.
• After installation, apply touch-up paint (the body color) onto the head of fuel filler lid mounting
screws.
JMKIA5270ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст