Infiniti QX56 (Z62). Manual — part 444
DLK-242
< REMOVAL AND INSTALLATION >
FRONT DOOR LOCK
7.
While pulling outside handle, remove door key cylinder assem-
bly (driver side) or outside handle escutcheon (passenger side).
8.
While pulling outside handle (1), slide toward rear of vehicle to
remove outside handle.
9.
Remove front gasket and rear gasket.
10. Slide toward rear of vehicle to remove outside handle bracket.
11. Disconnect door lock cable from outside handle bracket.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• When installing key rod, rotate key rod holder until a click is felt.
• Check door lock cable is properly engaged with outside handle bracket.
• After installation, check door open/close, lock/unlock operation.
JMKIA0560ZZ
JMKIA0524ZZ
JMKIA2652ZZ
REAR DOOR LOCK
DLK-243
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REAR DOOR LOCK
Exploded View
INFOID:0000000006226101
DOOR LOCK
DOOR LOCK : Removal and Installation
INFOID:0000000006226102
REMOVAL
1.
Remove outside handle and outside handle bracket. Refer to
DLK-244, "OUTSIDE HANDLE : Removal
2.
Remove door lock assembly TORX bolts.
3.
Disconnect door lock actuator connector, and then remove door lock assembly.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Check door lock cables are properly engaged with inside handle and outside handle.
• After installation, check door open/close, lock/unlock operation.
INSIDE HANDLE
1.
Outside handle escutcheon
2.
Rear gasket
3.
TORX bolt
4.
Door lock assembly
5.
Cable clip
6.
Door finisher cap
7.
Inside handle
8.
Outside handle bracket
9.
Front gasket
10. Outside handle
: Pawl
: Vehicle front
Refer to
JMKIA5267GB
DLK-244
< REMOVAL AND INSTALLATION >
REAR DOOR LOCK
INSIDE HANDLE : Removal and Installation
INFOID:0000000006226103
REMOVAL
1.
Remove rear door finisher. Refer to
INT-16, "Removal and Installation"
.
2.
Remove inside handle escutcheon. Refer to
3.
Remove inside handle mounting screws, and then remove inside handle.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Check door lock cables are properly engaged with inside handle.
• After installation, check door open/close, lock/unlock operation.
OUTSIDE HANDLE
OUTSIDE HANDLE : Removal and Installation
INFOID:0000000006226104
REMOVAL
1.
Fully close rear door glass.
2.
Remove rear door finisher. Refer to
INT-16, "Removal and Installation"
.
3.
Remove sealing screen.
NOTE:
Cat the buty-tape so that some parts of the buty-tape do not remain on the sealing screen, if the sealing
screen is reused.
4.
Remove door side grommet, and loosen TORX bolt from grom-
met hole.
5.
While pulling outside handle, remove outside handle escutch-
eon.
6.
While pulling outside handle (1), slide toward rear of vehicle to
remove outside handle.
: TORX bolt
JMKIA0025ZZ
JMKIA5342ZZ
JMKIA0524ZZ
REAR DOOR LOCK
DLK-245
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
7.
Remove front gasket and rear gasket.
8.
Slide toward rear of vehicle to remove outside handle bracket.
9.
Disconnect door lock cable from outside handle bracket.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Check door lock cable is properly engaged with outside handle bracket.
• After installation, check door open/close, lock/unlock operation.
JMKIA2652ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст