Infiniti QX56 (Z62). Manual — part 645
EM-20
< PERIODIC MAINTENANCE >
DRIVE BELTS
PERIODIC MAINTENANCE
DRIVE BELTS
Exploded View
INFOID:0000000006289524
Checking
INFOID:0000000006289525
WARNING:
Be sure to perform the these steps when engine is stopped.
• Check that the indicator (C) (notch on fixed side) of each auto-tensioner is within the possible use range (A).
NOTE:
• Check the each auto-tensioners indication when the engine is cold.
• When new drive belts is installed, the indicator (notch on fixed side) should be within the range (B) in the
figure.
• Visually check all drive belts for wear, damage or cracks.
• If the indicator (notch on fixed side) is out of the possible use range or drive belts are damaged, replace drive
belts.
Tension Adjustment
INFOID:0000000006289526
Removal and Installation
INFOID:0000000006289527
REMOVAL
1.
Move reservoir tank to the position without the hindrance for work. Refer to
.
1.
Drive belt
2.
Power steering oil pump pulley
3.
Alternator pulley
4.
Crankshaft pulley
5.
A/C compressor
6.
Idler pulley
7.
Cooling fan pulley
8.
Water pump pulley
9.
Drive belt auto-tensioner
A.
Possible use range
B.
Range when new drive belt is in-
stalled
C.
Indicator
D.
View D
JPBIA3264ZZ
DRIVE BELTS
EM-21
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
2.
Install wrench (A) on drive belt auto tensioner pulley bolt, move
in the direction of arrow (loosening direction of tensioner) as
shown.
CAUTION:
• Never place hand in a location where pinching may occur
if the holding tool accidentally comes off.
• Never loosen the hexagonal part in center of auto ten-
sioner pulley (1) (Never turn it clockwise). If turned clock-
wise, the complete auto tensioner must be replaced as a
unit, including the pulley.
3.
Under the above condition, insert a metallic bar (B) of approxi-
mately 6 mm (0.24 in) in diameter (hexagonal bar wrench shown
as example in the figure) through the holding boss to lock auto tensioner pulley arm.
4.
Remove drive belt.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
• Check drive belts are securely installed around all pulleys.
• Check drive belts are correctly engaged with the pulley groove.
• Check for engine oil and engine coolant are not adhered drive belts and pulley groove.
Inspection
INFOID:0000000006289528
INSPECTION AFTER INSTALLATION
• Turn crankshaft pulley clockwise several times to equalize tension between each pulley, and then confirm
tension of drive belts at indicator (notch on fixed side) is within the possible use range. Refer to
JPBIA3484ZZ
EM-22
< PERIODIC MAINTENANCE >
AIR CLEANER FILTER
AIR CLEANER FILTER
Exploded View
INFOID:0000000006289529
Removal and Installation
INFOID:0000000006289530
REMOVAL
NOTE:
• The viscous paper type filter does not need cleaning between replacement intervals.
• Replace the air filter as necessary for periodic maintenance. Refer to
MA-6, "Introduction of Periodic Mainte-
.
1.
Unhook clips, and lift air cleaner case (upper).
2.
Remove air cleaner filter from air cleaner case.
INSTALLATION
Install is the reverse order of removal.
1.
Resonator
2.
Adapter
3.
Air cleaner case (lower)
4.
Air cleaner filter
5.
Air cleaner case (upper)
6.
Mass air flow sensor
7.
Air duct
8.
Clamp
Vehicle front
for symbols in the figure.
JPBIA3260GB
SPARK PLUG
EM-23
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
SPARK PLUG
Exploded View
INFOID:0000000006289531
Removal and Installation
INFOID:0000000006289532
REMOVAL
1.
Remove engine cover. Refer to
.
2.
Remove ignition coil. Refer to
.
3.
Remove spark plug with a spark plug wrench (commercial ser-
vice tool).
INSTALLATION
Note the following item, installa is the reverse order of removal.
CAUTION:
1.
Ignition coil (No. 2, 4)
2.
Ignition coil (No. 6, 8)
3.
Spark plug
4.
Rocker cover (bank 2)
5.
Rocker cover (bank 1)
6.
Ignition coil (No. 1, 3)
7.
Ignition coil (No. 5, 7)
Refer to
for symbols in the figure.
JSBIA0388GB
a
: 14 mm (0.55 in)
JPBIA0030ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст