Infiniti QX56 (Z62). Manual — part 646
EM-24
< PERIODIC MAINTENANCE >
SPARK PLUG
Install ignition coil marked with an identification mark (A) on
cylinder No. 5, 6, 7 and 8.
Inspection
INFOID:0000000006289533
INSPECTION AFTER REMOVAL
Use the standard type spark plug for normal condition.
CAUTION:
• Never drop or impact spark plug.
• Never use a wire brush for cleaning.
• If plug tip is covered with carbon, use spark plug cleaner to
clean.
• Measure spark plug gap. When it exceeds the limit, replace spark plug even if it is within the speci-
fied replacement mileage. Refer to
• Spark plug gap adjustment is not required between replace-
ment intervals.
: Engine front
JPBIA3471ZZ
Spark plug (Standard type)
: Refer to
Cleaner air pressure
: Less than 588 kPa (5.9 bar, 6 kg/cm
2
, 85 psi)
Cleaning time
: Less than 20 seconds
SMA773C
JPBIA0031ZZ
ENGINE COVER
EM-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
REMOVAL AND INSTALLATION
ENGINE COVER
Exploded View
INFOID:0000000006289534
Removal and Installation
INFOID:0000000006289535
REMOVAL
CAUTION:
Never damage or scratch engine cover when installing or removing.
1.
Remove mounting bolts.
2.
Pull forward and remove engine cover.
3.
Remove bracket (front) and bracket (rear).
INSTALLATION
Installation is the reverse order of removal.
1.
Engine cover
2.
Bracket (front)
3.
Intake manifold
4.
Bracket (rear)
for symbols in the figure.
JPBIA3313GB
EM-26
< REMOVAL AND INSTALLATION >
DRIVE BELT AUTO TENSIONER AND IDLER PULLEY
DRIVE BELT AUTO TENSIONER AND IDLER PULLEY
Exploded View
INFOID:0000000006289536
Removal and Installation
INFOID:0000000006289537
Removal
CAUTION:
The complete drive belt auto-tensioner must be replaced as a unit, including the pulley.
1.
Remove drive belts. Refer to
• Keep auto-tensioner pulley arm locked after drive belt is removed.
2.
Remove drive belt auto-tensioner.
• Keep auto-tensioner pulley arm locked to install or remove auto-tensioner.
CAUTION:
Never loosen the hexagonal part in center of drive belt auto tensioner pulley (Never turn it clock-
wise). If turned clockwise, the complete drive belt auto tensioner must be replaced as a unit,
including the pulley.
3.
Remove idler pulley.
Installation
Installation is the reverse order of removal.
CAUTION:
Never swap the pulley between new and old drive belt auto tensioner.
1.
Drive belt auto-tensioner
2.
Idler pulley
3.
Fan bracket
Refer to
for symbols in the figure.
JPBIA3971GB
AIR CLEANER AND AIR DUCT
EM-27
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
AIR CLEANER AND AIR DUCT
Exploded View
INFOID:0000000006289538
Removal and Installation
INFOID:0000000006289539
REMOVAL
NOTE:
Mass air flow sensor is removable under the car-mounted condition.
1.
Remove engine cover. Refer to
.
2.
Disconnect mass air flow sensor harness connector.
3.
Remove air cleaner case and mass air flow sensor assembly and air duct by disconnecting their joints.
• Add matching marks, if necessary for easier installation.
4.
Remove mass air flow sensor from air cleaner case, if necessary.
CAUTION:
Handle mass air flow sensor according to the following instructions.
• Never impact it.
• Never disassemble it.
• Never touch its sensor.
5.
Disconnect PCV hose from air duct.
6.
Remove air duct.
7.
Remove air cleaner filter.
8.
Remove air cleaner case (lower).
9.
Remove adapter.
10. If remove resonator (location in wheel house), refer to following.
a.
Remove LH front wheel and tire.
b.
Remove fender protector. Refer to
EXT-23, "FENDER PROTECTOR : Exploded View"
c.
Remove resonator.
INSTALLATION
1.
Resonator
2.
Adapter
3.
Air cleaner case (lower)
4.
Air cleaner filter
5.
Air cleaner case (upper)
6.
Mass air flow sensor
7.
Air duct
8.
Clamp
Vehicle front
Refer to
for symbols in the figure.
JPBIA3260GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст