Infiniti QX56 (Z62). Manual — part 437
DLK-214
< SYMPTOM DIAGNOSIS >
SQUEAK AND RATTLE TROUBLE DIAGNOSES
PIIB8742E
HOOD
DLK-215
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REMOVAL AND INSTALLATION
HOOD
Exploded View
INFOID:0000000006226062
HOOD ASSEMBLY
HOOD ASSEMBLY : Removal and Installation
INFOID:0000000006226063
CAUTION:
• Operate with two workers, because of its heavy weight.
• Use protective tape or shop cloth to protect from damage during removal and installation.
REMOVAL
1.
Support hood assembly with the proper material to prevent it from falling.
WARNING:
Bodily injury may occur if no proper material is holding hood open when removing hood stay.
1.
Hood assembly
2.
Hood front seal
3.
Radiator core seal
4.
Hood insulator
5.
Hood side bumper
6.
Clip
7.
Hood stay
8.
Stud ball
9.
Hood bumper rubber
10. Hood hinge
: Clip
Refer to
JMKIA5477GB
DLK-216
< REMOVAL AND INSTALLATION >
HOOD
2.
Remove the metal clip (3) located on the connection between
the hood stay (1) and the stud ball (2) (hood side), by using a
flatted-blade screwdriver (A).
3.
Disengage the stud ball from the hood stay (hood side).
4.
Remove hood hinge mounting nuts on the hood to remove the hood assembly.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Before installing the hood hinge, apply anticorrosive agent onto the mounting surface of the vehicle
body.
• After installing, perform hood fitting adjustment. Refer to
DLK-216, "HOOD ASSEMBLY : Adjust-
HOOD ASSEMBLY : Adjustment
INFOID:0000000006226064
JMKIA2255ZZ
JMKIA5818GB
HOOD
DLK-217
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Check the clearance and the surface height between hood and each part by visually and touching.
If the clearance and the surface height are out of specification, adjust them according to the procedures
shown below.
Unit: mm (in)
1.
Remove hood lock and adjust the surface height of hood, bumper molding and front fender according to
the fitting standard dimension, by rotating hood bumper rubber.
2.
Loosen hood hinge mounting nuts on the hood.
3.
Adjust the clearance of hood, bumper molding and front fender according to the fitting standard dimen-
sion, for the hood.
4.
Temporarily tighten hood lock.
5.
Adjust A and B shown in the figure to the following value with hood's own weight by dropping it from
approximately 200 mm (7.874 in) height or by pressing hood lightly [approximately 29 N (3.0 kg, 6.5lb)].
6.
Install as static closing force of hood is 680N (69.0 kg, 502lb) or less.
7.
After adjustment, tighten hood hinge mounting nuts to the specified torque.
CAUTION:
• Before installing hood hinge, apply anticorrosive agent onto the mounting surface of the vehicle
body.
• Check hood hinge rotating part for poor lubrication. If necessary, apply body grease.
1.
Hood assembly
2.
Hood bumper rubber
3.
Hood hinge
4.
Hood lock assembly
5.
Front grille
6.
Bumper molding
7.
Front fender
Refer to
Portion
Standard
Difference
(RH/LH,
MAX)
Hood – Front grille
A – A
D
Clearance
3.7 – 8.3 (0.146 – 0.327)
—
E Surface height
(-0.9) – (+3.9) [(-0.035) –
(+0.154)]
—
Hood – Bumper molding
B – B
F
Clearance
1.2 – 5.8 (0.047 – 0.228)
2.2 (0.087)
G Surface height
(-2.4) –– (+0.094)]
2.2 (0.087)
Hood – Front fender
C – C
H
Clearance
2.5 – 4.5 (0.098 – 0.177)
1.0 (0.039)
I
Surface height
(-1.0) – (+1.0) [(-0.039 –
(+0.039)]
—
1.
Hood striker
2.
Primary latch
3.
Secondary striker
4.
Secondary latch
A
: 20.0 mm (0.787 in)
B
: 6.8 mm (0.268 in)
PIIB5794E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст