Infiniti QX56 (Z62). Manual — part 438
DLK-218
< REMOVAL AND INSTALLATION >
HOOD
• After installation, apply touch-up paint (the body color) onto the head of hood hinge mounting
bolts and nuts.
HOOD HINGE
HOOD HINGE : Removal and Installation
INFOID:0000000006226065
REMOVAL
1.
Remove hood assembly. Refer to
DLK-215, "HOOD ASSEMBLY : Removal and Installation"
2.
Remove front fender cover. Refer to
3.
Remove front fender mounting bolt.
4.
Remove hood hinge mounting bolts, and then remove hood hinge.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Before installation of hood hinge, apply anticorrosive agent onto the mounting surface of the vehicle
body.
• After installation, apply touch-up paint (the body color) onto the head of the hinge mounting bolts
and nuts.
• After installation, perform hood fitting adjustment. Refer to
DLK-216, "HOOD ASSEMBLY : Adjust-
HOOD STAY
HOOD STAY : Removal and Installation
INFOID:0000000006226066
REMOVAL
1.
Support hood assembly with a proper material to prevent it from falling.
WARNING:
Bodily injury may occur if no proper material is holding the hood open when removing the hood
stay.
2.
Remove the metal clip (3) located on the connection between
the hood stay (1) and the stud ball (2) (hood side), by using a
flat-bladed screwdriver (A).
3.
Disengage the stud ball from the hood stay (hood side).
4.
Repeat the same operation to disengage the stud ball from the
hood stay (body side), then remove the hood stay.
INSTALLATION
Install in the reverse order of removal.
HOOD STAY : Disposal
INFOID:0000000006226067
1.
Fix hood stay (1) using a vise (C).
2.
Using hacksaw (A) slowly make 2 holes in the hood stay, in
numerical order as shown in the figure.
CAUTION:
• When cutting a hole on hood stay, always cover a hack-
saw using a shop cloth (B) to avoid scattering metal frag-
ments or oil.
• Wear eye protection (safety glasses).
• Wear gloves.
JMKIA2255ZZ
JMKIA3336ZZ
HOOD
DLK-219
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
A:
20 mm (0.787 in)
B:
Cut at the groove.
JMKIA3609ZZ
DLK-220
< REMOVAL AND INSTALLATION >
RADIATOR CORE SUPPORT
RADIATOR CORE SUPPORT
Exploded View
INFOID:0000000006226068
Removal and Installation
INFOID:0000000006226069
RADIATOR CORE SUPPORT UPPER
Removal
CAUTION:
When removing radiator core support upper, be careful not to damage the painted surface.
1.
Remove bumper molding, bumper molding stay LH and RH. Refer to
EXT-13, "Removal and Installation"
2.
Remove fixing clips, and then radiator upper seal.
3.
Remove horn (LOW and HIGH). Refer to
HRN-6, "Removal and Installation"
.
4.
Remove exhaust gas / outside oder sensor. Refer to
HAC-151, "Removal and Installation"
.
5.
Disconnect refrigerant pressure sensor harness connector.
1.
Radiator upper seal
2.
Radiator core support upper
3.
Air guide seal LH
4.
Air guide seal RH
5.
Radiator side seal RH
6.
Radiator lower seal RH
7.
Radiator lower seal LH
8.
Radiator side seal LH
9.
Radiator core support main
Refer to for symbols in the figure.
JMKIA5479GB
RADIATOR CORE SUPPORT
DLK-221
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
6.
Disconnect all harness clips.
7.
Remove hood lock assembly. Refer to
DLK-238, "Removal and Installation"
8.
Remove fixing clips of air guide seal.
9.
Remove mounting bolts, and then remove power steering oil
cooler. Refer to
.
CAUTION:
Put a wooden block (A) under the oil cooler (1) to prevent
the oil cooler from falling.
10. Remove radiator mounting bolts. Refer to
CO-13, "Removal and Installation"
.
11. Remove mounting bolts, and then radiator core support upper.
Installation
Note the following items, and then install in the reverse order of removal.
CAUTION:
• If aluminum plate remains to the body side when removing radiator core support upper, be sure to
pinch aluminum plate between radiator core support upper and hoodledge upper when installing
radiator core support upper, for preventing electric corrosion.
• When installing radiator core support upper, be careful not to damage the painted surface.
RADIATOR CORE SUPPORT LOWER
Removal
1.
Remove front bumper fascia, bumper retainer and Bumper retainer bracket CTR. Refer to
2.
Remove fixing clips, and then air guide seal and radiator side seal.
3.
Remove ambient sensor. Refer to
HAC-147, "Removal and Installation"
.
4.
Remove crash zone sensor. Refer to
SR-22, "Removal and Installation"
.
5.
Remove all harness clips.
6.
Remove mounting bolts, and then remove radiator core support main.
Installation
Install in the reverse order of removal.
JMKIA5480ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст