Infiniti QX56 (Z62). Manual — part 764
GW-24
< REMOVAL AND INSTALLATION >
REAR DOOR GLASS
8.
Operate the power window switch to raise or lower the door win-
dow until the glass mounting bolts can be seen.
9.
Remove the rear door glass mounting bolts.
10. Raise rear door glass up and hold it with a suction lifter (A).
11. Disconnect rear door power window motor harness connector.
12. Remove rear door regulator mounting nuts.
13. Remove rear door power window motors mounting bolts.
14. Remove rear door regulator from rear door panel.
15. Securely place rear door glass down inside rear door panel.
16. Remove rear door glass run.
17. Remove rear door sash mounting bolts and screw, and then pull
it up to remove.
CAUTION:
Be careful not to scratch or damage rear door glass with
rear door sash.
18. Remove rear door glass from rear door panel as shown by the
figure.
: Bolt
JMKIA1789ZZ
PIIB3511J
JMKIA5272ZZ
JMKIA5273ZZ
REAR DOOR GLASS
GW-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
19. Slide partition glass toward the vehicle and remove it as shown
in the figure.
INSTALLATION
Install in the reverse order of removal.
Inspection and Adjustment
INFOID:0000000006220831
SYSTEM INITIALIZATION
Initialize the system if any of the following work has been done. Refer to
Initialization
Follow the steps below after installing each component to the vehicle. Refer to
.
FITTING INSPECTION
• Check that the glass is fit securely into the sash groove.
• Lower the glass slightly [approximately 10 to 20 mm (0.394 to 0.787 in)], and check that the clearance to the
sash is parallel. Loosen the regulator mounting bolts, guide rail mounting bolts, and glass and guide rail
mounting bolts to correct the glass position if the clearance between the glass and sash is not parallel.
JMKIA5274ZZ
GW-26
< REMOVAL AND INSTALLATION >
REAR REGULATOR
REAR REGULATOR
Exploded View
INFOID:0000000006220832
Removal and Installation
INFOID:0000000006220833
REMOVAL
1.
Remove rear door finisher. Refer to
INT-16, "Removal and Installation"
.
2.
Remove rear door inside seal.
3.
Remove rear door outside molding. Refer to
EXT-32, "Removal and Installation"
4.
Remove rear pull handle bracket mounting bolts and then remove it.
5.
Disconnect rear door speaker harness connector.
6.
Remove the sealing screen with a cutter tool.
NOTE:
Cut the butyl-tape so that some parts of the butyl-tape do not remain on the sealing screen, if the sealing
screen is reused.
7.
Reconnect the rear door power window switch.
1.
Rear door panel
2.
Rear door glass run
3.
Partition sash
4.
Partition glass
5.
Rear door glass
6.
Rear door regulator
7.
Rear power window motor
8.
Rear door pull handle bracket
9.
Rear door sealing screen
10. Grommet
11.
Rear door inside seal
JMKIA5209ZZ
REAR REGULATOR
GW-27
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
8.
Operate the power window switch to raise or lower the door win-
dow until the glass mounting bolts can be seen.
9.
Remove the rear door glass mounting bolts.
10. Raise rear door glass up and hold it with a suction lifter (A).
11. Disconnect rear door power window motor harness connector.
12. Remove rear door regulator mounting nuts.
13. Remove rear door power window motors mounting bolts.
14. Remove rear door regulator from rear door panel.
INSTALLATION
Install in the reverse order of removal.
Disassembly and Assembly
INFOID:0000000006220834
DISASSEMBLY
Remove rear power window motor from rear door regulator.
ASSEMBLY
Assemble in the reverse order of disassembly.
Inspection and Adjustment
INFOID:0000000006220835
SYSTEM INITIALIZATION
Initialize the system if any of the following work has been done. Refer to
WHEN REMOVING BATTERY NEGATIVE TERMINAL : Description"
Initialization
Follow the steps below after installing each component to the vehicle. Refer to
VICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Special Repair Requirement"
FITTING INSPECTION
• Check that the glass is fit securely into the sash groove.
• Lower the glass slightly [approximately 10 to 20 mm (0.394 to 0.787 in)], and check that the clearance to the
sash is parallel. Loosen the regulator mounting bolts, guide rail mounting bolts, and glass and guide rail
mounting bolts to correct the glass position if the clearance between the glass and sash is not parallel.
: Bolt
JMKIA1789ZZ
PIIB3511J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст