Infiniti QX56 (Z62). Manual — part 763
GW-20
< REMOVAL AND INSTALLATION >
FRONT DOOR GLASS
13. Remove front door lower sash mounting bolt and pull it out of front door panel.
INSTALLATION
Install in the reverse order of removal.
Inspection and Adjustment
INFOID:0000000006220824
SYSTEM INITIALIZATION
Initialize the system if any of the following work has been done. Refer to
Initialization
Follow the steps below after installing each component to the vehicle. Refer to
.
FITTING INSPECTION
• Check that the glass is fit securely into the sash groove.
• Lower the glass slightly [approximately 10 to 20 mm (0.394 to 0.787 in)], and check that the clearance to the
sash is parallel. Loosen the regulator mounting bolts, guide rail mounting bolts, and glass and guide rail
mounting bolts to correct the glass position if the clearance between the glass and sash is not parallel.
FRONT REGULATOR
GW-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
FRONT REGULATOR
Exploded View
INFOID:0000000006220825
Removal and Installation
INFOID:0000000006220826
REMOVAL
1.
Remove front door glass. Refer to
GW-19, "Removal and Installation"
2.
Disconnect front power window motor harness connector.
3.
Remove front door regulator mounting bolts.
4.
Remove front door power window motor mounting bolts.
5.
Remove front door regulator and front door power window motor from front door panel.
INSTALLATION
Install in the reverse order of removal.
Disassembly and Assembly
INFOID:0000000006220827
DISASSEMBLY
1.
Remove front door regulator from front door panel.
2.
Remove front door power window motor from front door regulator.
ASSEMBLY
Assemble in the reverse order of disassembly.
1. Front door panel
2.
Front door glass run
3.
Front door glass
4.
Front door regulator
5.
Front door power window motor
6.
Front door pull handle bracket
7.
Front door sealing screen
8.
Front door lower sash
9.
Grommet
10. Front door inside seal
11.
Power window controller
JMKIA5208ZZ
GW-22
< REMOVAL AND INSTALLATION >
FRONT REGULATOR
Inspection and Adjustment
INFOID:0000000006220828
SYSTEM INITIALIZATION
Initialize the system if any of the following work has been done. Refer to
Initialization
Follow the steps below after installing each component to the vehicle. Refer to
.
FITTING INSPECTION
• Check that the glass is fit securely into the sash groove.
• Lower the glass slightly [approximately 10 to 20 mm (0.394 to 0.787 in)], and check that the clearance to the
sash is parallel. Loosen the regulator mounting bolts, guide rail mounting bolts, and glass and guide rail
mounting bolts to correct the glass position if the clearance between the glass and sash is not parallel.
REAR DOOR GLASS
GW-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
REAR DOOR GLASS
Exploded View
INFOID:0000000006220829
Removal and Installation
INFOID:0000000006220830
REMOVAL
1.
Remove rear door finisher. Refer to
INT-16, "Removal and Installation"
.
2.
Remove rear door inside seal.
3.
Remove rear door outside molding. Refer to
EXT-32, "Removal and Installation"
.
4.
Remove rear door pull handle bracket mounting bolts and remove it.
5.
Disconnect rear door speaker harness connector.
6.
Remove the rear door sealing screen with a cutter tool.
NOTE:
Cut the butyl-tape so that some parts of the butyl-tape do not remain on the rear door sealing screen, if the
sealing screen is reused.
7.
Reconnect the rear door power window switch.
1.
Rear door panel
2.
Rear door glass run
3.
Partition sash
4.
Partition glass
5.
Rear door glass
6.
Rear door regulator
7.
Rear power window motor
8.
Rear door pull handle bracket
9.
Rear door sealing screen
10. Grommet
11.
Rear door inside seal
JMKIA5209ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст