Infiniti QX56 (Z62). Manual — part 1394
WW-54
< SYMPTOM DIAGNOSIS >
FRONT WIPER DOES NOT OPERATE
3.
With operating the front wiper switch, check the status of “FR WIP REQ”.
Is the inspection result normal?
YES
>> Replace IPDM E/R.
NO
>> GO TO 6.
6.
CHECK COMBINATION SWITCH
Perform the inspection of the combination switch. Refer to
Is combination switch normal?
YES
>> Replace BCM. Refer to
BCS-81, "Removal and Installation"
NO
>> Repair or replace the applicable parts.
Monitor item
Condition
Monitor status
FR WIP REQ
Front wiper switch HI
On
Hi
Off
Stop
Front wiper switch LO
On
Low
Off
Stop
HEADLAMP WASHER NOZZLE AND TUBE
WW-55
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
REMOVAL AND INSTALLATION
HEADLAMP WASHER NOZZLE AND TUBE
Exploded View
INFOID:0000000006220393
Hydraulic Layout
INFOID:0000000006220394
1.
Headlamp washer nozzle cover
2.
Headlamp washer nozzle assembly
3.
Headlamp washer nozzle retainer
4.
Headlamp washer nozzle bracket
5.
Front bumper fascia
: Pawl
JMLIA1096ZZ
1.
Headlamp washer nozzle assembly
LH
2.
Headlamp washer tube
3.
Headlamp washer tube (tank side)
4.
Headlamp washer nozzle assembly
RH
5.
Front bumper fascia
A.
Metal clip
JMLIA1097ZZ
WW-56
< REMOVAL AND INSTALLATION >
HEADLAMP WASHER NOZZLE AND TUBE
Removal and Installation
INFOID:0000000006220395
REMOVAL
1.
Pull out headlamp washer nozzle from bumper fascia, disen-
gage pawl (A), and then remove headlamp washer nozzle cover
(1).
2.
Remove front bumper fascia. Refer to
EXT-13, "Removal and Installation"
.
3.
Disconnect headlamp washer tube joint.
4.
Remove headlamp washer nozzle retainer.
5.
Remove headlamp washer nozzle bracket.
6.
Remove headlamp washer nozzle from the front bumper fascia.
INSTALLATION
Install in the reverse order of removal.
Inspection
INFOID:0000000006220396
HEADLAMP WASHER NOZZLE SPRAY POSITION INSPECTION
CAUTION:
Replace headlamp washer nozzle assembly with a new part if headlamp washer jet position is outside
the headlamp illumination area shown in the figure.
• Check that headlamp washer injection is certainly on headlamp
illumination area.
• Check the headlamp washer injection range as shown in the fig-
ure.
JPLIA1030ZZ
JMLIA1098ZZ
a
: 67.8 mm (2.31 in)
B
: 83.2 mm (3.04 in)
C
: 316.2 mm (12.13 in)
JMLIA1099ZZ
HEADLAMP WASHER NOZZLE AND TUBE
WW-57
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
• Check the headlamp washer nozzle spray angle.
Outside (A)
Inside (B)
NOTE:
This drawing shows the parts of the headlamp washer nozzle (LH). The headlamp washer nozzle (RH) is
symmetrical of this drawing.
1.
Headlamp washer nozzle (outside)
2.
Headlamp washer nozzle (inside)
JPLIA1033ZZ
a
: 30
°±
3
°
b
: 70
°±
3
°
c
: 55
°±
3
°
d
: 45
°±
3
°
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст