Infiniti QX56 (Z62). Manual — part 491
DLN-164
< UNIT DISASSEMBLY AND ASSEMBLY >
[FRONT FINAL DRIVE: R180A]
SIDE SHAFT
UNIT DISASSEMBLY AND ASSEMBLY
SIDE SHAFT
Exploded View
INFOID:0000000006222387
1.
Bushing
2.
Bearing cap
3.
Side bearing
4.
Side bearing adjusting washer
5.
Drive pinion
6.
Pinion height adjusting washer
7.
Pinion rear bearing
8.
Collapsible spacer
9.
Gasket
10. Drain plug
11.
Side oil seal (left side)
12. Pinion front bearing
13. Front oil seal
14. Companion flange
15. Drive pinion lock nut
16. Gear carrier
17. Side shaft
18. Side shaft bearing
19. Snap ring
20. Snap ring
21. Side oil seal (right side)
22. Drive gear
23. Differential case assembly
24. Housing spacer
25. Filler plug
26. Carrier cover
A:
Oil seal lip
B:
Screw hole
C.
Comply with the assembly proce-
dure when tightening. Refer to
: Apply gear oil.
: Apply anti-corrosion oil.
JPDID0390GB
SIDE SHAFT
DLN-165
< UNIT DISASSEMBLY AND ASSEMBLY >
[FRONT FINAL DRIVE: R180A]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
Disassembly
INFOID:0000000006222388
1.
Drain the differential gear oil if necessary.
2.
Remove the carrier cover bolts
3.
Remove carrier cover to insert the seal cutter (A) [SST:
KV10111100 (J-37228)] between gear carrier and carrier cover.
CAUTION:
• Never damage the mating surface.
• Never insert flat-bladed screwdriver, this will damage the
mating surface.
4.
Remove side oil seal (right side) with a suitable tool.
CAUTION:
Never damage gear carrier.
5.
Remove snap ring (hole side) with a suitable tool.
6.
Remove differential side shaft assembly out of gear carrier with
a suitable tool.
NOTE:
Tap on differential side shaft assembly from side gear side.
7.
Remove snap ring (differential side shaft side).
: Apply multi-purpose grease.
: Apply Genuine Silicone RTV or equivalent. Refer to
GI-22, "Recommended Chemical Products and Sealants"
.
: Apply Genuine High Strength Thread Locking Sealant or equivalent. Refer to
GI-22, "Recommended Chemical Products
Refer to
for symbols not described above.
PDIA0699E
PDIA0713E
PDIA0714E
JPDID0383ZZ
DLN-166
< UNIT DISASSEMBLY AND ASSEMBLY >
[FRONT FINAL DRIVE: R180A]
SIDE SHAFT
8.
Press differential side shaft out of differential side shaft bearing.
CAUTION:
Never drop differential side shaft.
9.
Perform inspection after disassembly. Refer to
Assembly
INFOID:0000000006222389
1.
Press differential side shaft bearing to differential side shaft.
CAUTION:
Never reuse differential side shaft bearing.
2.
Install snap ring (differential side shaft side).
3.
Install differential side shaft assembly into gear carrier.
4.
Install snap ring (hole side).
5.
Install side oil seal (right side) until it becomes flush with the
gear carrier, with the drifts (A and B).
CAUTION:
• Never reuse side oil seal.
• When installing, never incline oil seal.
• Apply multi-purpose grease onto oil seal lips and gear oil
onto the circumference of oil seal.
Inspection
INFOID:0000000006222390
INSPECTION AFTER DISASSEMBLY
Side Shaft
• If it is chipped (by friction), cracked, damaged, or unusually worn, replace.
Bearing
• Clean up the disassembled parts.
• If any chipped (by friction), pitted, worn, rusted or scratched marks, or unusual noise from the bearing is
observed, replace as a bearing assembly (as a new set).
Oil Seal
• Whenever disassembled, replace.
• If wear, deterioration of adherence (sealing force lips), or damage is detected on the lips, replace them.
PDIA0718E
PDIA0719E
A: Drift [SST: ST30720000 (J-25405)]
B: Drift [SST: ST27863000 (
—
)]
PDIA0828E
DIFFERENTIAL ASSEMBLY
DLN-167
< UNIT DISASSEMBLY AND ASSEMBLY >
[FRONT FINAL DRIVE: R180A]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
DIFFERENTIAL ASSEMBLY
Exploded View
INFOID:0000000006222391
1.
Bushing
2.
Bearing cap
3.
Side bearing
4.
Side bearing adjusting washer
5.
Drive pinion
6.
Pinion height adjusting washer
7.
Pinion rear bearing
8.
Collapsible spacer
9.
Gasket
10. Drain plug
11.
Side oil seal (left side)
12. Pinion front bearing
13. Front oil seal
14. Companion flange
15. Drive pinion lock nut
16. Gear carrier
17. Side shaft
18. Side shaft bearing
19. Snap ring
20. Snap ring
21. Side oil seal (right side)
22. Drive gear
23. Differential case assembly
24. Housing spacer
25. Filler plug
26. Carrier cover
A:
Oil seal lip
B:
Screw hole
C.
Comply with the assembly proce-
dure when tightening. Refer to
: Apply gear oil.
: Apply anti-corrosion oil.
: Apply multi-purpose grease.
JPDID0390GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст