Infiniti QX56 (Z62). Manual — part 490
DLN-160
< REMOVAL AND INSTALLATION >
[FRONT FINAL DRIVE: R180A]
SIDE OIL SEAL
SIDE OIL SEAL
Exploded View
INFOID:0000000006222383
Removal and Installation
INFOID:0000000006222384
REMOVAL
1.
Drain gear oil. Refer to
.
2.
Remove the drive shafts from the front final drive assembly. Refer to
FAX-22, "Removal and Installation"
3.
Remove the side oil seal using suitable tool.
CAUTION:
Never damage gear carrier.
INSTALLATION
1.
Drive the new side oil seal in evenly until it becomes flush with
the gear carrier using drifts (A and B).
CAUTION:
• Never reuse side oil seal.
• Never incline the new side oil seal when installing.
• Apply multi-purpose grease to the lips and differential
gear oil to the circumference of the new side oil seal.
1.
Front final drive assembly
2.
Side oil seal
A.
Oil seal lip
: Apply gear oil.
: Apply multi-purpose grease.
Refer to
for symbols not described on the above.
JPDID0387ZZ
LDIA0173E
A: Drift [SST: ST30720000 (J-25405)]
B: Drift [SST: ST27863000 (
—
)]
PDIA0826E
SIDE OIL SEAL
DLN-161
< REMOVAL AND INSTALLATION >
[FRONT FINAL DRIVE: R180A]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
2.
Install drive shaft. Refer to
FAX-22, "Removal and Installation"
.
3.
Refill gear oil to the final drive and check oil level. Refer to
.
4.
Check the final drive for oil leakage. Refer to
.
DLN-162
< UNIT REMOVAL AND INSTALLATION >
[FRONT FINAL DRIVE: R180A]
FRONT FINAL DRIVE ASSEMBLY
UNIT REMOVAL AND INSTALLATION
FRONT FINAL DRIVE ASSEMBLY
Exploded View
INFOID:0000000006222385
Removal and Installation
INFOID:0000000006222386
REMOVAL
1.
Drain the differential gear oil. Refer to
.
2.
Remove the drive shafts. Refer to
FAX-22, "Removal and Installation"
3.
Remove the front propeller shaft from the front final drive assembly. Refer to
.
4.
Disconnect the breather hose from the front final drive assembly.
5.
Support the front final drive assembly using a suitable jack.
6.
Remove the front final drive assembly bolts, then remove the front final drive assembly with a power tool.
CAUTION:
Secure the front final drive assembly to a suitable jack while removing it.
INSTALLATION
Note the following, and installation is in the reverse order of removal.
CAUTION:
Check that there are no pinched or restricted areas on the breather hose caused by bending or wind-
ing when installing it.
1.
Front final drive assembly
Refer to
for symbols in figure.
JPDID0388GB
FRONT FINAL DRIVE ASSEMBLY
DLN-163
< UNIT REMOVAL AND INSTALLATION >
[FRONT FINAL DRIVE: R180A]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
• Install the breather hose (1) as shown in the figure.
- Install the breather hose (1) of final side with the paint mark (A)
facing vehicle front, and insert the breather hose until dimension
(B) shown as follows.
CAUTION:
• Never reuse hose clamp.
• Install the hose clamp with the tab facing vehicle front.
- Be sure to fix the breather hose in (C) position.
• If remove the bracket (2), align stopper part (D) to part (E) of sus-
pension mounting bracket (3), and tighten the mounting bolt (4) to
specified torque.
• When oil leaks while removing final drive assembly, check oil level
after the installation. Refer to
: Vehicle front
B:
20 mm (0.79 in)
Specified torque:
8.3 N•m (0.85 kg-m, 73 in-lb)
JPDID0389ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст