Infiniti QX56 (Z62). Manual — part 1323
AIR BREATHER HOSE
TM-201
< REMOVAL AND INSTALLATION >
[7AT: RE7R01B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
• To fix A/T air breather hose (1) to the clip (2), face the A/T air
breather hose paint mark (A) rearward and observe the instal-
lation position shown in the figure.
• To install air breather cap (3), face the arrow “
” (B) toward
the right side of the vehicle as shown in the figure.
• To fix A/T air breather hose (1) to the clip (2), face the A/T air
breather hose paint mark (A) upward and observe the installa-
tion position shown in the figure.
JSDIA1641ZZ
JSDIA1642ZZ
TM-202
< REMOVAL AND INSTALLATION >
[7AT: RE7R01B]
FLUID COOLER SYSTEM
FLUID COOLER SYSTEM
Exploded View
INFOID:0000000006226907
Removal and Installation
INFOID:0000000006226908
REMOVAL
1.
Remove front grille. Refer to
EXT-19, "Removal and Installation"
2.
Remove reservoir tank. Refer to
CO-13, "Removal and Installation"
.
3.
Remove radiator upper seal. Refer to
.
4.
Remove air guide seal (RH). Refer to
.
5.
Remove A/T fluid cooler hose C and D from A/T fluid cooler.
6.
Remove liquid tank mounting bolt (A). Refer to
7.
Remove A/T fluid cooler mounting bolt (B).
8.
Remove radiator mounting bolts and tilt radiator to the vehicle
rear. Refer to
9.
Remove A/T fluid cooler bracket (C) from radiator (1), and
remove A/T fluid cooler (2) from the vehicle.
CAUTION:
• Be careful not to damage A/T fluid cooler core.
• Be careful not to damage condenser core, condenser pipe
and liquid tank.
1.
A/T assembly
2.
Copper washer
3.
A/T fluid cooler tube A
4.
A/T fluid cooler tube D
5.
Clip
6.
Hose clamp
7.
A/T fluid cooler hose E
8.
A/T fluid cooler hose A
9.
A/T fluid cooler hose B
10. A/T fluid cooler tube B
11.
A/T fluid cooler tube C
12. A/T fluid cooler hose D
13. A/T fluid cooler
14. A/T fluid cooler hose C
15. A/T fluid warmer
Refer to
for symbols in the figure.
JSDIA1595GB
JSDIA1687ZZ
FLUID COOLER SYSTEM
TM-203
< REMOVAL AND INSTALLATION >
[7AT: RE7R01B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
10. Remove control cable mounting bracket. Refer to
TM-178, "Removal and Installation"
.
11. Remove front under cover. Refer to
EXT-25, "Removal and Installation"
.
12. Remove A/T fluid cooler hoses and A/T fluid cooler tubes.
CAUTION:
Be careful not to bend A/T fluid cooler tubes.
NOTE:
Cap or plug openings to prevent fluid from spilling.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• Never reuse copper washers.
• Be careful not to damage A/T fluid cooler core.
• Be careful not to damage condenser core, condenser pipe and liquid tank.
• Refer to the following when installing A/T fluid cooler hoses.
*: Refer to the illustrations for the specific position each hose clamp tab.
- The illustrations indicate the view from the hose ends.
- When installing hose clamps center line of each hose clamp tab
should be positioned as shown in the figure.
- Insert A/T fluid cooler hoses according to dimension “L” described below.
Hose name
Hose end
Paint mark
Position of hose clamp
*
A/T fluid cooler hose A
A/T fluid cooler tube A side
Facing upward
A
A/T fluid warmer side
Facing upward
C
A/T fluid cooler hose B
A/T fluid warmer side
Facing leftward
E
A/T fluid cooler tube B side
Facing downward
B
A/T fluid cooler hose C
A/T fluid cooler tube B side
Facing rightward
G
A/T fluid cooler side
Facing upward
F
A/T fluid cooler hose D
A/T fluid cooler side
—
C
A/T fluid cooler tube C side
—
G
A/T fluid cooler hose E
A/T fluid cooler tube C side
Facing downward
B
A/T fluid cooler tube D side
Facing rightward
D
H
: Vehicle upper
I
: Vehicle front
JSDIA1639ZZ
TM-204
< REMOVAL AND INSTALLATION >
[7AT: RE7R01B]
FLUID COOLER SYSTEM
- Set hose clamps (1) at the both ends of A/T fluid cooler hoses (2)
with dimension “A” from the hose edge.
- Hose clamp should not interfere with the bulge of fluid cooler tube.
Inspection and Adjustment
INFOID:0000000006226909
INSPECTION AFTER INSTALLATION
Check A/T fluid leakage. Refer to
ADJUSTMENT AFTER INSTALLATION
Adjust A/T fluid level. Refer to
.
A/T fluid cool-
er hose (1)
Insertion side tube (2)
Tube type
Dimension “L”
A/T fluid cool-
er hose A
A/T fluid cooler tube A
A
30 mm (1.18 in)
[End reaches the
2-stage bulge
(C).]
A/T fluid warmer tube
A/T fluid cool-
er hose B
A/T fluid warmer tube
B
Insert the hose
until the hose
touches the A/T
fluid warmer.
A/T fluid cooler tube B
A
30 mm (1.18 in)
[End reaches the
2-stage bulge
(C).]
A/T fluid cool-
er hose C
A/T fluid cooler tube B
A/T fluid cooler tube
A/T fluid cool-
er hose D
A/T fluid cooler tube
A/T fluid cooler tube C
A/T fluid cool-
er hose E
A/T fluid cooler tube C
A/T fluid cooler tube D
JSDIA1640ZZ
Dimension “A”
: 5 – 9 mm (0.20 – 0.35 in)
SCIA8123E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст