Infiniti QX56 (Z62). Manual — part 1321
REAR OIL SEAL
TM-193
< REMOVAL AND INSTALLATION >
[7AT: RE7R01B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
2WD : Inspection
INFOID:0000000006228062
INSPECTION AFTER INSTALLATION
Check A/T fluid leakage. Refer to
.
ADJUSTMENT AFTER INSTALLATION
Adjust A/T fluid level. Refer to
.
4WD
4WD : Exploded View
INFOID:0000000006226902
4WD : Removal and Installation
INFOID:0000000006226903
REMOVAL
1.
Remove transfer assembly from A/T assembly. Refer to
DLN-137, "Removal and Installation"
.
2.
Remove rear oil seal (1) with a flat-bladed screwdriver (A).
CAUTION:
Never scratch adapter case assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
1.
A/T
2.
Rear oil seal
Refer to
JSDIA1726ZZ
JPDIA0038ZZ
TM-194
< REMOVAL AND INSTALLATION >
[7AT: RE7R01B]
REAR OIL SEAL
• As shown in the figure, use the drift [64 mm (2.52 in) dia. commer-
cial service tool] (A) to drive rear oil seal into adapter case assem-
bly until it is flush.
CAUTION:
• Never reuse rear oil seal.
• Apply ATF to rear oil seal.
4WD : Inspection and Adjustment
INFOID:0000000006226904
INSPECTION AFTER INSTALLATION
Check A/T fluid leakage. Refer to
ADJUSTMENT AFTER INSTALLATION
Adjust A/T fluid level. Refer to
.
JPDIA0040ZZ
OUTPUT SPEED SENSOR
TM-195
< REMOVAL AND INSTALLATION >
[7AT: RE7R01B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
OUTPUT SPEED SENSOR
2WD
2WD : Exploded View
INFOID:0000000006228119
2WD : Removal and Installation
INFOID:0000000006228120
REMOVAL
1.
Disconnect the battery cable from the negative terminal.
2.
Drain ATF through drain plug.
3.
Separate propeller shaft assembly. Refer to
1.
A/T
2.
Oil pan gasket
3.
Oil pan
4.
Clip
5.
Oil pan mounting bolt
6.
Overflow plug
7.
Drain plug
8.
Drain plug gasket
9.
Magnet
10.
Output speed sensor
11.
Self-sealing bolt
12.
Bracket
13.
Rear extension
*
: Apply Genuine Anaerobic Liquid Gasket or equivalent. Refer to
GI-22, "Recommended Chemical Products and Sealants"
.
Refer to
for symbols not described on the above.
JSDIA1925GB
TM-196
< REMOVAL AND INSTALLATION >
[7AT: RE7R01B]
OUTPUT SPEED SENSOR
4.
Remove clips (1).
5.
Remove oil pan (2) and oil pan gasket.
6.
Support A/T assembly with a transmission jack.
CAUTION:
When setting transmission jack, place wooden blocks to
prevent from damaging control valve & TCM and transmis-
sion case.
7.
Remove rear engine mounting cross member with power tool. Refer to
8.
Remove engine mounting insulator (rear). Refer to
9.
Remove tightening bolts for rear extension assembly and trans-
mission case.
10. Tap rear extension assembly with a soft hammer (A).
CAUTION:
Be careful not to damage rear extension case.
11. Remove rear extension assembly (with needle bearing) from
transmission case.
: Vehicle front
: Oil pan mounting bolt
1 :
Bracket
A
: Bolt
B
: Self-sealing bolt
JSDIA1591ZZ
JSDIA1845ZZ
JPDIA0027ZZ
SCIA3431E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст