Infiniti QX56 (Z62). Manual — part 1320
PARKING COMPONENTS
TM-189
< REMOVAL AND INSTALLATION >
[7AT: RE7R01B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
11. Remove parking gear (1) from output shaft (2).
12. Remove seal rings (1) from output shaft.
13. Remove needle bearing (1) from rear extension.
14. Remove parking actuator support (1) from rear extension.
15. Remove parking pawl (with return spring) (1) and pawl shaft (2)
from rear extension.
JPDIA0029ZZ
JPDIA0030ZZ
SCIA6179J
JPDIA0031ZZ
JPDIA0032ZZ
TM-190
< REMOVAL AND INSTALLATION >
[7AT: RE7R01B]
PARKING COMPONENTS
16. Remove return spring (1) from parking pawl (2).
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• Never reuse seal rings and drain plug gasket.
• Apply petroleum jelly to needle bearing and seal rings.
• Insert the tip of parking rod between the parking pawl and the parking actuator support when assem-
bling the rear extension assembly.
• Refer to the followings installing rear extension assembly.
- Apply recommended sealant (Genuine Anaerobic Liquid Gasket or
equivalent. Refer to
GI-22, "Recommended Chemical Products
.) to rear extension assembly as shown in the figure.
CAUTION:
Completely remove all moisture, oil and old sealant, etc. from
the transmission case and rear extension assembly mounting
surfaces.
- Tighten rear extension assembly bolts to the specified torque.
2WD : Inspection
INFOID:0000000006233260
INSPECTION AFTER REMOVAL
SCIA6180J
Sealant starting
point and end-
point (A)
: Start and finish point shall be in
the center of two bolts.
Overlap width of
sealant starting
point and end-
point (B)
: 3 – 5 mm (0.12 – 0.20 in)
Sealant width (C)
: 1.0 – 2.0 mm (0.04 – 0.08 in)
Sealant height (C)
: 0.4 – 1.0 mm (0.016 – 0.04 in)
JSDIA1855ZZ
1
: Bracket
A
: Bolt
B
: Self-sealing bolt
JSDIA1845ZZ
PARKING COMPONENTS
TM-191
< REMOVAL AND INSTALLATION >
[7AT: RE7R01B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
If the contact surface on parking actuator support (1), parking pawl
(2) and etc. has excessive wear, abrasion, bend, or any other dam-
age, replace the components.
INSPECTION AFTER INSTALLATION
Check A/T fluid leakage. Refer to
.
JPDIA0034ZZ
TM-192
< REMOVAL AND INSTALLATION >
[7AT: RE7R01B]
REAR OIL SEAL
REAR OIL SEAL
2WD
2WD : Exploded View
INFOID:0000000006228060
2WD : Removal and Installation
INFOID:0000000006228061
REMOVAL
1.
Remove propeller shaft assembly. Refer to
DLN-144, "Removal and Installation"
2.
Remove rear oil seal (1) using a flat-bladed screwdriver (A).
CAUTION:
Be careful not to scratch rear extension assembly.
INSTALLATION
Note the following and install in the reverse order of removal.
• As shown in the figure, use the drift [SST: ST33400001 (J-26082)]
(A) to drive rear oil seal into rear extension assembly until it is
flush.
CAUTION:
• Never reuse rear oil seal.
• Apply ATF to rear oil seal.
1.
A/T
2.
Rear oil seal
Refer to
for symbols in the figure.
JSDIA1843ZZ
JPDIA0037ZZ
JPDIA0039ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст