Infiniti QX56 (Z62). Manual — part 1197
SR-22
< REMOVAL AND INSTALLATION >
CRASH ZONE SENSOR
CRASH ZONE SENSOR
Exploded View
INFOID:0000000006216179
Removal and Installation
INFOID:0000000006216180
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
• Never use the air tools or electric tools for servicing.
REMOVAL
1.
Remove the front under cover. Refer to
EXT-25, "Removal and Installation"
2.
Disconnect the crash zone sensor harness connector.
3.
Remove the crash zone sensor fixing nut, and then remove crash zone sensor.
CAUTION:
• Never impact the crash zone sensor.
• Replace the crash zone sensor if it has been dropped or sus-
tained an impact.
1.
Crash zone sensor
Refer to
for symbols in the figure.
JMHIA1583GB
JMHIA0009ZZ
CRASH ZONE SENSOR
SR-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
• Replace the crash zone sensor of deployed driver air bag and deployed front passenger air bag.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
• Never use the old fixing nut after removal, replace with the new nut.
• Never damage the harness connector while installing.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT-III. Refer to
SRC-19, "CONSULT-III Function"
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
SR-24
< REMOVAL AND INSTALLATION >
SIDE AIR BAG (SATELLITE) SENSOR
SIDE AIR BAG (SATELLITE) SENSOR
Exploded View
INFOID:0000000006113063
Removal and Installation
INFOID:0000000006113064
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
• Never use the air tools or electric tools for servicing.
REMOVAL
SIDE AIR BAG FRONT (SATELLITE) SENSOR LH
1.
Remove the center pillar lower garnish LH. Refer to
INT-22, "CENTER PILLAR LOWER GARNISH :
.
2.
Remove the side air bag front (satellite) sensor LH fixing nut.
3.
Disconnect the side air bag front (satellite) sensor LH harness connector, and then remove side air bag
front (satellite) sensor LH.
SIDE AIR BAG FRONT (SATELLITE) SENSOR RH
1.
Remove the center pillar lower garnish RH. Refer to
INT-22, "CENTER PILLAR LOWER GARNISH :
.
1.
Side air bag rear (satellite) sensor
2.
Bracket *
3.
Side air bag front (satellite) sensor
: Vehicle front
*: Side air bag rear (satellite) sensor RH side only
Refer to
for symbols in the figure.
JMHIA1477GB
SIDE AIR BAG (SATELLITE) SENSOR
SR-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
2.
Remove the front seat belt retractor. Refer to
SB-6, "SEAT BELT RETRACTOR : Removal and Installa-
3.
Remove the side air bag front (satellite) sensor RH fixing nut.
4.
Disconnect the side air bag front (satellite) sensor RH harness connector, and then remove side air bag
front (satellite) sensor RH.
SIDE AIR BAG REAR (SATELLITE) SENSOR LH
1.
Remove the luggage side lower finisher LH. Refer to
INT-36, "LUGGAGE SIDE LOWER FINISHER :
.
2.
Remove the side air bag rear (satellite) sensor LH fixing nut.
3.
Disconnect the side air bag rear (satellite) sensor LH harness connector, and then remove side air bag
rear (satellite) sensor LH.
SIDE AIR BAG REAR (SATELLITE) SENSOR RH
1.
Remove the luggage side lower finisher RH. Refer to
INT-36, "LUGGAGE SIDE LOWER FINISHER :
.
2.
Remove the shield bracket fixing screw, and then remove shield bracket.
3.
Remove the side air bag rear (satellite) sensor RH fixing nut.
4.
Disconnect the side air bag rear (satellite) sensor RH harness connector, and then remove side air bag
rear (satellite) sensor RH.
CAUTION:
• Never impact the side air bag (satellite) sensor.
• Replace the side air bag (satellite) sensor if it has been
dropped or sustained an impact.
• Replace the satellite sensor of deployed front side air bag module and deployed side curtain air bag
module.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
• Never use the old fixing nut after removal, replace with the new nut.
• Never damage the harness connector while installing
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT-III. Refer to
SRC-19, "CONSULT-III Function"
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
JMHIA0009ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст