Infiniti QX56 (Z62). Manual — part 847
INT-36
< REMOVAL AND INSTALLATION >
LUGGAGE FLOOR TRIM
LUGGAGE SIDE LOWER FINISHER
LUGGAGE SIDE LOWER FINISHER : Removal and Installation
INFOID:0000000006220261
REMOVAL
1.
Lift up the seat base, tilt seatback forward, and fold down second seat forward.
2.
Remove second seat belt anchor. Refer to
SB-13, "SEAT BELT RETRACTOR : Removal and Installation"
.
3.
Remove third seat. Refer to
SE-138, "Removal and Installation"
.
4.
Remove third seat belt anchor. Refer to
SB-19, "SEAT BELT RETRACTOR : Removal and Installation"
5.
Remove luggage floor board center and both luggage lower boards. Refer to
REAR BOARD : Removal and Installation"
.
6.
Remove luggage rear plate. Refer to
INT-35, "LUGGAGE REAR PLATE : Removal and Installation"
7.
Remove rope hook (1) mounting bolt using a socket wrench (A),
and then remove rope hook.
8.
Disengage luggage side lower finisher fixing clip (1) using a
small flat-bladed screwdriver (A) as shown by the arrow in the
figure, and then remove clip.
9.
Remove luggage side lower finisher.
1.
Disengage luggage side lower finisher (1) fixing clips and
pawls.
2.
Disconnect luggage room power socket harness connector (LH side only).
3.
Disconnect fold down switch harness connector (RH side only).
4.
Disconnect reclining switch harness connector (LH and RH).
5.
Remove luggage side lower finisher.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
JMJIA4043ZZ
JMJIA4042ZZ
: Clip
: Pawl
JMJIA4044ZZ
LUGGAGE FLOOR TRIM
INT-37
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
• Visually check the clips and pawls for deformation and damage during installation. Replace with new
ones if necessary.
• When installing luggage side lower finisher, check that clips and pawls are securely fitted in body
panel holes, and press them in.
REAR PILLAR FINISHER
REAR PILLAR FINISHER : Removal and Installation
INFOID:0000000006220262
REMOVAL
1.
Remove luggage side lower finisher.
INT-36, "LUGGAGE SIDE LOWER FINISHER : Removal and Instal-
.
2.
Disengage lower side of rear pillar finisher fixing clip.
3.
Pull rear pillar upper garnish (1) from inside passenger room, disengage rear pillar upper garnish upper
side fixing pawl as shown in the following figure, and then remove rear pillar upper garnish from body
panel (2).
CAUTION:
Be careful not to apply excessive force when removing rear pillar finisher. Otherwise, pawl may be
damaged and fragments may drop in body panel holes on body.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Replace rear pillar finisher with a new part after removal. Never reuse rear pillar finisher.
• Visually check the clip and pawl for deformation and damage during installation. Replace with new
ones if necessary.
• When installing rear pillar finisher, check that clip and pawl are securely fitted in body panel holes,
and press them in.
BACK PILLAR GARNISH
BACK PILLAR GARNISH : Removal and Installation
INFOID:0000000006220263
REMOVAL
1.
Remove luggage side lower finisher.
INT-36, "LUGGAGE SIDE LOWER FINISHER : Removal and Instal-
.
2.
Remove cap of back door finisher side (LH), and then remove stud ball. Refer to
SUPPORT ROD : Removal and Installation"
(LH side only).
3.
Disengage back pillar garnish (1) fixing clips and pawl using a
remover tool (A), and then remove back pillar garnish.
JMJIA1176ZZ
: Clip
: Pawl
JMJIA4045ZZ
INT-38
< REMOVAL AND INSTALLATION >
LUGGAGE FLOOR TRIM
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Visually check the clips and pawl for deformation and damage during installation. Replace with new
ones if necessary.
• When installing back pillar garnish, check that clips and pawl are securely fitted in body panel holes,
and press them in.
LUGGAGE SIDE UPPER FINISHER
LUGGAGE SIDE UPPER FINISHER : Removal and Installation
INFOID:0000000006220264
REMOVAL
1.
Remove luggage side lower finisher. Refer to
INT-36, "LUGGAGE SIDE LOWER FINISHER : Removal
2.
Remove rear pillar finisher. Refer to
INT-37, "REAR PILLAR FINISHER : Removal and Installation"
3.
Remove back pillar garnish. Refer to
INT-37, "BACK PILLAR GARNISH : Removal and Installation"
.
4.
Remove luggage side upper finisher.
1.
Remove mounting bolts (1).
2.
Disengage luggage side upper finisher (2) fixing clips using
a remover tool (A), and then remove luggage side upper fin-
isher (3).
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Visually check the clips for deformation and damage during installation. Replace with new ones if
necessary.
• When installing luggage side upper finisher, check that clips are securely fitted in body panel holes,
and press them in.
: Clip
JMJIA4046ZZ
BACK DOOR TRIM
INT-39
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
BACK DOOR TRIM
Exploded View
INFOID:0000000006220265
Removal and Installation
INFOID:0000000006220266
REMOVAL
1.
Fully open back door.
1.
Back door finisher lower
2.
Auto back door switch finisher
3.
Pull handle
4.
Back door assembly
5.
Back door finisher side RH
6.
Back door finisher upper
7.
Back door finisher side LH
8.
Cap
9.
Lamp mask
10. Emergency handle mask
: Clip
: Pawl
: Metal clip
JMJIA4421ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст