Infiniti QX56 (Z62). Manual — part 846
INT-32
< REMOVAL AND INSTALLATION >
HEADLINING
• Personal lamp assembly. Refer to
INL-77, "Removal and Installation"
.
• Rear ventilator grille assembly. Refer to
VTL-13, "REAR VENTILATOR GRILLE : Removal and Installa-
• Headlining harness.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Be careful not to bend headlining when installing.
• First install metal clips of map lamp assembly and clips of the rear end of headlining for positioning.
LUGGAGE FLOOR TRIM
INT-33
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
LUGGAGE FLOOR TRIM
Exploded View
INFOID:0000000006220258
1.
Rear pillar finisher LH
2.
Luggage upper finisher LH
3.
Luggage side lower finisher LH
4.
Back pillar garnish LH
5.
Rope hook
6.
Clip
7.
Luggage lower board LH
8.
Luggage floor finisher LH
9.
Luggage floor bracket
JMJIA4308ZZ
INT-34
< REMOVAL AND INSTALLATION >
LUGGAGE FLOOR TRIM
*: Reclining switch (22) is also installed on luggage side lower finisher LH (3).
LUGGAGE FLOOR REAR BOARD
LUGGAGE FLOOR REAR BOARD : Removal and Installation
INFOID:0000000006220259
REMOVAL
1.
Open luggage floor board center (1).
2.
Remove both bolts shown by the arrows in the figure, and then
remove luggage floor board center.
3.
Remove luggage floor finishers (LH/RH).
1.
Remove bolts shown by the arrows in the figure.
2.
Disengage luggage floor finisher (1) fixing pawl and clip
using a remover tool (A), and then remove luggage side fin-
isher.
4.
Remove both luggage floor rear boards.
1.
Fold down the third seat forward.
2.
Remove rope hook (1) mounting bolt using a socket wrench
(A), and then remove rope hook.
10. Luggage floor board center
11. Tool box
12. Luggage rear plate
13. Luggage rear plate mask
14. Child anchor cover
15. Luggage floor finisher RH
16. Luggage lower board RH
17. Fold down switch
18. Back pillar garnish RH
19. Luggage side lower finisher RH
20. Luggage upper finisher RH
21. Rear pillar finisher RH
22. Reclining switch*
: Clip
: Pawl
JMJIA4027ZZ
: Clip
: Pawl
JMJIA4028ZZ
JMJIA4029ZZ
LUGGAGE FLOOR TRIM
INT-35
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
3.
Disengage luggage floor board RH (1) fixing pawls and
clips, and then remove luggage side finisher.
4.
Disengage luggage floor board LH (2) fixing pawls and clips,
and then remove luggage side finisher.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Visually check the clips and pawls for deformation and damage during installation. Replace with new
ones if necessary.
• When installing luggage floor rear board, check that clips and pawls are securely fitted in body panel
holes, and press them in.
LUGGAGE REAR PLATE
LUGGAGE REAR PLATE : Removal and Installation
INFOID:0000000006220260
REMOVAL
1.
Open luggage floor board center.
2.
Remove luggage floor finishers (LH and RH).
1.
Remove nuts shown by the arrows in the figure.
2.
Disengage luggage floor finisher (1) fixing clip and pawl
using a remover tool (A), and then remove luggage side fin-
isher.
3.
Disengage luggage rear plate (1) fixing clips and pawls using a
remover tool (A), and then remove luggage rear plate.
4.
Remove luggage rear plate mask from luggage rear plate.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Visually check the clips and pawls for deformation and damage during installation. Replace with new
ones if necessary.
• When installing luggage rear plate, check that clips and pawls are securely fitted in body panel
holes, and press them in.
: Clip
: Pawl
JMJIA4030ZZ
: Clip
: Pawl
JMJIA4028ZZ
: Clip
: Pawl
JMJIA4041ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст