Infiniti QX56 (Z62). Manual — part 1114
CK SUSP INDICATOR LAMP DOES NOT TURN OFF
SCS-93
< SYMPTOM DIAGNOSIS >
[AIR LEVELIZER CONTROL SYSTEM]
C
D
F
G
H
I
J
K
L
M
A
B
SCS
N
O
P
CK SUSP INDICATOR LAMP DOES NOT TURN OFF
Description
INFOID:0000000006256096
• CK SUSP indicator lamp turns ON while driving the vehicle.
• CK SUSP indicator lamp does not turn ON after the completion of standard vehicle height setting.
Diagnosis Procedure
INFOID:0000000006256097
1.
STANDARD VEHICLE HEIGHT SETTING
Perform “STANDARD VEHICLE HEIGHT SETTING”. Refer to
Does CK SUSP indicator lamp turn OFF?
YES
>> INSPECTION END
NO
>> Replace the air levelizer control module. Refer to
SCS-94
< REMOVAL AND INSTALLATION >
[AIR LEVELIZER CONTROL SYSTEM]
AIR LEVELIZER CONTROL MODULE
REMOVAL AND INSTALLATION
AIR LEVELIZER CONTROL MODULE
Exploded View
INFOID:0000000006256098
Removal and Installation
INFOID:0000000006256099
REMOVAL
CAUTION:
Never impact on air levelizer control module when removing or installing air levelizer control module.
1.
Disconnect battery cable from negative terminal.
2.
Remove luggage side lower finisher (LH). Refer to
.
3.
Disconnect air levelizer control module harness connector.
4.
Remove the air levelizer control module.
INSTALLATION
Install in the reverse order of removal.
Adjustment
INFOID:0000000006256100
After air levelizer control module is replaced, perform “STANDARD VEHICLE HEIGHT SETTING”. Refer to
.
1.
Air levelizer control module
: Vehicle front
for symbols not described on the above.
JSEIA0237GB
AIR COMPRESSOR/AIR TUBE
SCS-95
< REMOVAL AND INSTALLATION >
[AIR LEVELIZER CONTROL SYSTEM]
C
D
F
G
H
I
J
K
L
M
A
B
SCS
N
O
P
AIR COMPRESSOR/AIR TUBE
Exploded View
INFOID:0000000006256101
Removal and Installation
INFOID:0000000006256102
REMOVAL
CAUTION:
Seal the removed part using vinyl tape for preventing dirt from getting on or entering the removed
part.
1.
Lift up the vehicle.
2.
Remove the cover.
3.
Disconnect the air compressor harness connector.
1.
Air tube A
2.
Air tube B
3.
Bracket
4.
Air compressor
5.
Clip
6.
Cover
7.
Insulator
8.
Washer
9.
Exhaust tube
10.
Exhaust tube connector
A.
To rear shock absorber (RH)
B.
To rear shock absorber (LH)
C.
To frame
: Vehicle front
Refer to
for symbols not described on the above.
JSEIA0227GB
SCS-96
< REMOVAL AND INSTALLATION >
[AIR LEVELIZER CONTROL SYSTEM]
AIR COMPRESSOR/AIR TUBE
4.
Using a small spanner, remove the air tube A (1) and B (2) from
air compressor.
CAUTION:
Be careful since air flows swiftly from air tube.
5.
Remove the exhaust tube (1) from exhaust tube connector (2).
6.
Remove the exhaust tube connector only when it is damaged.
7.
Remove the exhaust tube from air compressor.
8.
Remove the air compressor from bracket.
9.
Rmove the bracket from vehicle.
10. Remove the air tube A and B from rear shock absorbers RH and
LH, according to the procedure in step 4.
11. Remove the air tube A and B from vehicle.
12. Perform inspection after removal. Rfer to
.
INSTALLATION
Note the following, and install in the reverse order of the removal.
• When installing air tube (1) to air compressor or shock absorber,
insert as shown in the figure.
• Dry each component thoroughly before installing, to prevent mois-
ture from entering air compressor.
JSEIA0238ZZ
JSEIA0239ZZ
JSEIA0240GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст