Infiniti QX56 (Z62). Manual — part 1317
A/T SHIFT SELECTOR
TM-177
< REMOVAL AND INSTALLATION >
[7AT: RE7R01B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
INSTALLATION
Note the following, and install in the reverse order of removal.
• When installing control cable (1) to A/T shift selector assembly (2),
check that control cable is fully pressed in with the ribbed (A) sur-
face facing upward.
• Refer to the followings when installing the selector lever knob to
the A/T shift selector assembly.
1.
Install the lock pin to the selector lever knob.
2.
Insert the shift lever knob into the shift lever until it clicks.
CAUTION:
• Install it straight, and never tap or apply any shock to
install it.
• Never press selector button.
Inspection and Adjustment
INFOID:0000000006226893
INSPECTION AFTER INSTALLATION
Check A/T position after adjusting A/T position. Refer to
.
ADJUSTMENT AFTER INSTALLATION
Adjust A/T position. Refer to
JPDIA0609ZZ
TM-178
< REMOVAL AND INSTALLATION >
[7AT: RE7R01B]
CONTROL CABLE
CONTROL CABLE
Exploded View
INFOID:0000000006226894
Removal and Installation
INFOID:0000000006226895
REMOVAL
1.
Remove center console assembly . Refer to
IP-25, "Removal and Installation"
.
2.
Remove cluster lid C cover and instrument center finisher LH. Refer to
IP-14, "Removal and Installation"
.
3.
Shift selector lever in “P” position.
4.
Remove control cable from A/T shift selector assembly.
5.
Remove control cable from manual lever and control cable mounting bracket.
1.
Control cable
2.
A/T shift selector assembly
3.
Lock plate
4.
Manual lever
5.
Washer
6.
Lock plate
7.
Bracket
8.
A/T assembly
A.
Retainer
for symbols in the figure.
JSDIA1589GB
CONTROL CABLE
TM-179
< REMOVAL AND INSTALLATION >
[7AT: RE7R01B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
6.
Remove retainer mounting bolts (
) according to the following
procedure.
a.
Separate propeller shaft assembly (front). Refer to
. (For 4WD models)
b.
Disconnect heated oxygen sensor 2 connectors (bank 1 and
bank 2). Refer to
c.
Remove exhaust front tube (RH and LH). Refer to
d.
Remove heat plates above three way catalyst (RH and LH).
e.
Remove control cable mounting bracket from A/T assembly.
f.
Remove retainer mounting bolts from dash panel.
7.
Remove control cable from the vehicle.
INSTALLATION
Note the following, and install in the reverse order of removal.
When installing control cable (1) to A/T shift selector assembly (2),
check that control cable is fully pressed in with the ribbed (A) surface
facing upward.
Inspection and Adjustment
INFOID:0000000006226896
INSPECTION AFTER INSTALLATION
Check A/T position after adjusting A/T position. Refer to
.
ADJUSTMENT AFTER INSTALLATION
Adjust A/T position. Refer to
JSDIA1677ZZ
JPDIA0609ZZ
TM-180
< REMOVAL AND INSTALLATION >
[7AT: RE7R01B]
SELECTOR LEVER POSITION INDICATOR
SELECTOR LEVER POSITION INDICATOR
Removal and Installation
INFOID:0000000006226897
REMOVAL
1.
Remove console finisher assembly. Refer to
IP-25, "Removal and Installation"
.
2.
Remove insert finisher (1).
3.
Remove selector lever position indicator (2).
INSTALLATION
Install in the reverse order of removal.
: Screw
JSDIA1646ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст