Infiniti QX80 (2021 year). Manual in english — page 7

2-18

Instruments and controls

cap if the Loose Fuel Cap warning
appears in the vehicle information dis-
play. If the fuel-filler cap is loose or
missing, tighten or install the cap and
continue to drive the vehicle. The
light should turn off after a few driving
trips. If the

light does not turn off

after a few driving trips, have the vehicle
inspected. It is recommended you visit an
INFINITI retailer for this service. You do
not need to have your vehicle towed to
the retailer.

.

Malfunction indicator light blinking — An

engine misfire has been detected which
may damage the emission control sys-
tem.
To reduce or avoid emission control
system damage:
1) Do not drive at speeds above 45

MPH (72 km/h).

2) Avoid hard acceleration or decelera-

tion.

3) Avoid steep uphill grades.
4) If possible, reduce the amount of

cargo being hauled or towed.

The malfunction indicator light may stop
blinking and remain on.
Have the vehicle inspected. It is recom-
mended you visit an INFINITI retailer for
this service. You do not need to have
your vehicle towed to the retailer.

CAUTION

Continued vehicle operation without
having the emission control system
checked and repaired as necessary could
lead to poor driveability, reduced fuel
economy, and possible damage to the
emission control system.

Master warning light

When the ignition switch is in the ON
position, the master warning light illumi-
nates when a warning message appears in
the vehicle information display.
See “Vehicle information display” (P.2-20).

Vehicle Dynamic Control

(VDC) off indicator light

When the ignition switch is in the ON
position, the Vehicle Dynamic Control
(VDC) off indicator light illuminates and then
turns off.
The light comes on when the vehicle dynamic
control off switch is pushed to OFF. This
indicates that the vehicle dynamic control
system is not operating.
When the 4L position is selected with the

Four-Wheel Drive (4WD) shift switch, the
VDC system is disabled and the VDC off
indicator light illuminates. (4WD models)
For additional information, see “Vehicle
Dynamic Control (VDC) system” (P.5-125).

Vehicle Dynamic Control

(VDC) warning light

The light will blink when the VDC system or
the traction control system is operating, thus
alerting the driver that the vehicle is nearing
its traction limits. The road surface may be
slippery.
When the VDC warning light illuminates
when the VDC system is turned on, this light
alerts the driver to the fact that the VDC
system’s fail-safe mode is operating, for
example the VDC or hill start assist system
may not be functioning properly. Have the
system checked. It is recommended you visit
an INFINITI retailer for this service. If a
malfunction occurs in the system, the VDC
system function will be canceled but the
vehicle is still driveable. For additional
information, see “Vehicle Dynamic Control
(VDC) system” (P.5-125).

WARNING/INDICATOR LIGHTS
(other)

See “Vehicle information display” (P.2-20).

Exterior light indicator

This indicator illuminates when the headlight
switch is turned to the AUTO,

or

position and the front parking lights, instru-
ment panel lights, rear combination lights,
license plate lights or headlights are on. The
indicator turns off when these lights are
turned off.

Front fog light indicator light

The front fog light indicator light illuminates
when the front fog lights are on. (See “Fog
light switch” (P.2-47).)

Front passenger air bag status

light

The front passenger air bag status light
(

) located on the instrument panel will be

lit and the passenger front air bag will be
OFF depending on how the front passenger
seat is being used.
For front passenger air bag status light
operation, see “INFINITI Advanced Air Bag
System (front seats)” (P.1-58).

High beam assist indicator

light

The indicator light illuminates when the
headlights come on while the headlight
switch is in the AUTO position with the high
beam selected. This indicates that the high
beam assist system is operational. (See
“High beam assist” (P.2-41).)

High beam indicator light

This light comes on when the headlight high
beam is on and goes out when the low beam
is selected.

TOW mode indicator light

This light will illuminate when the TOW
mode is selected while the engine is running.
(See “TOW mode” (P.5-122).)

Turn signal/hazard indicator

lights

The light flashes when the turn signal switch
lever or hazard switch is turned on.

AUDIBLE REMINDERS

Key reminder chime

A chime will sound if the driver side door is
opened while the ignition switch is pushed to
the ACC position. Make sure the ignition
switch is pushed to the OFF position, and
take the Intelligent Key with you when
leaving the vehicle.

Light reminder chime

A chime will sound when the driver side door
is opened with the light switch in the

or

position and the ignition switch in the

ACC, OFF or LOCK position.
Turn the light switch off when you leave the
vehicle.

Parking brake reminder chime

The chime will sound if the vehicle is driven
at more than 4 MPH (7 km/h) with the
parking brake applied. Stop the vehicle and
release the parking brake.

Brake pad wear warning

The disc brake pads have audible wear
warnings. When a brake pad requires repla-
cement, it will make a high pitched scraping
sound when the vehicle is in motion. This
scraping sound will first occur only when the
brake pedal is depressed. After more wear of

Instruments and controls

2-19

2-20

Instruments and controls

the brake pad, the sound will always be
heard even if the brake pedal is not
depressed. Have the brakes checked as soon
as possible if the warning sound is heard.

JVI1272X

The vehicle information display

is located

between the tachometer and the speed-
ometer, and it displays the warnings and
information. The following items are also
displayed if the vehicle is equipped with
them:

.

Odometer/twin trip odometer

— “Odometer/twin trip odometer” (P.2-

7)

.

Automatic Transmission (AT)

— “Driving the vehicle” (P.5-17).

.

Four-Wheel Drive (4WD) system

— “INFINITI all-mode 4WD

®

” (P.5-113)

.

Cruise control system

— “Cruise control” (P.5-62)

.

Intelligent Cruise Control (ICC) system

— “Intelligent Cruise Control (ICC)” (P.5-

64)

.

Distance Control Assist (DCA) system

— “Distance Control Assist (DCA)” (P.5-

84)

.

Intelligent Key system

— “Intelligent Key system” (P.3-7)
— “Push-button ignition switch” (P.5-

12)

.

Lane Departure Warning (LDW)/Lane

Departure Prevention (LDP)
— “Lane Departure Warning (LDW)/

Lane Departure Prevention (LDP)”
(P.5-22)

.

Blind Spot Warning (BSW)

— “Blind Spot Warning (BSW)” (P.5-31)

.

Blind Spot Intervention

®

(BSI)

— “Blind Spot Intervention

®

(BSI)” (P.5-

41)

.

Back-up Collision Intervention (BCI) sys-

tem
— “Back-up Collision Intervention (BCI)”

(P.5-53)

.

Forward Emergency Braking (FEB) with

pedestrian detection system
— “Forward Emergency Braking (FEB)

with pedestrian detection” (P.5-95)

.

Predictive Forward Collision Warning

(PFCW) system

VEHICLE INFORMATION DISPLAY

2-22

Instruments and controls

WAC0221X

WAC0380X

Instruments and controls

2-23

2-24

Instruments and controls

OPERATIONAL INDICATORS

1. No Key Detected

This warning appears when the Intelligent
Key is left outside the vehicle with the
ignition switch in the ON position. Make
sure the Intelligent Key is inside the vehicle.
See “Intelligent Key system” (P.3-7) for more
details.

2. Key ID Incorrect

This warning appears when the ignition
switch is pushed from the OFF position
and the Intelligent Key is not recognized by
the system. You cannot start the engine with
an unregistered key.
See “Intelligent Key system” (P.3-7).

3. Key Battery Low

This indicator appears when the Intelligent
Key battery is running out of power.
If this indicator appears, replace the battery
with a new one. (See “Intelligent Key battery
replacement” (P.8-21).)

4. Key System Error: See Owner’s
Manual

This warning appears if there is a malfunc-
tion in the Intelligent Key system. If this
warning appears while the engine is

stopped, it may be impossible to start the
engine.
If this warning appears while the engine is
running, you can drive the vehicle. However
in these cases, have the system checked. It is
recommended you visit an INFINITI retailer
for this service.

5. Key Registration Complete

This indicator appears when a new Intelli-
gent Key is registered to the vehicle.

6. Push brake and start switch to
drive

This indicator appears when the shift lever is
in the P (Park) position.
This indicator also appears when the vehicle
has been started using the Remote Engine
Start function (if so equipped).
This indicator means that the engine will
start by pushing the ignition switch with the
brake pedal depressed. You can start the
engine from any position of the ignition
switch.

7. Push Ignition to OFF

After the Shift to Park warning illuminates,
the warning will illuminate if the ignition
switch is placed in the ACC position when
the shift lever moves into the P (Park)
position.

To turn off the warning, place the ignition
switch in the ON position and then in the
LOCK position.

8. Shift to Park

This warning appears when the ignition
switch is pushed to stop the engine with
the shift lever in any position except the P
(Park) position.
If this warning appears, move the shift lever
to the P (Park) position or push the ignition
switch to the ON position.
An inside warning chime will also sound. (See
“Intelligent Key system” (P.3-7).)

9. Engine start operation for Intel-
ligent Key system indicator (if I-Key
battery level is low)

This indicator appears when the Intelligent
Key battery is running out of power and
when the Intelligent Key system and vehicle
are not communicating normally.
If this indicator appears, touch the ignition
switch with the Intelligent Key while depres-
sing the brake pedal. (See “Intelligent Key
battery discharge” (P.5-14).)

10. Release Parking Brake

This warning appears when the vehicle
speed is above 4 MPH (7 km/h) and the

parking brake is applied. Stop the vehicle and
release the parking brake.

11. Low Fuel

This warning appears when the fuel level in
the tank is getting low. Refuel as soon as it is
convenient, preferably before the fuel gauge
reaches the 0 (Empty) position.

There is a small reserve of fuel remaining in
the tank when the fuel gauge reaches the 0
(Empty) position.

12. Low Washer Fluid

This warning appears when the washer tank
fluid is at a low level. Add washer fluid as
necessary. (See “Window washer fluid” (P.8-
10).)

13. Loose Fuel Cap

This warning appears when the fuel-filler
cap is not tightened correctly after the
vehicle has been refueled. (See “Fuel-filler
cap” (P.3-27).)

14. Tire Pressure Low Add Air

This warning appears when the low tire
pressure warning light in the meter illumi-
nates and low tire pressure is detected. The
warning appears each time the ignition
switch is placed in the ON position as long
as the low tire pressure warning light

remains illuminated. If this warning appears,
stop the vehicle and adjust the tire pressure
to the recommended COLD tire pressure
shown on the Tire and Loading Information
label. (See “Low tire pressure warning light”
(P.2-16) and “Tire Pressure Monitoring
System (TPMS)” (P.5-5).)

15. SNOW mode indicator

This indicator appears when SNOW mode is
selected by the SNOW mode switch. (See
“SNOW mode” (P.5-122).)

16. Four-Wheel Drive (4WD) shift
indicator (4WD models)

This indicator shows the Four-Wheel Drive
(4WD) driving mode (AUTO, 4HI or 4LO)
that is selected by the 4WD shift switch.
(See “INFINITI all-mode 4WD

®

” (P.5-113).)

17. Door/liftgate open warning
(ignition switch is in the ON posi-
tion)

This warning appears if any of the doors
and/or the liftgate are open or not closed
securely. The vehicle icon indicates which
door or the liftgate is open on the display.

18. Power will turn off to save the
battery

This warning appears after a period of time
if the ignition switch is in ACC or ON
position.

19. Power turned off to save the
battery

This warning appears after the ignition
switch is automatically turned OFF to save
the battery.

20. Light reminder warning

This warning appears when the driver side
door is opened with the headlight switch is
left ON and the ignition switch is placed in
the OFF or LOCK position. Place the head-
light switch in OFF or AUTO position. For
additional information, see “Headlight and
turn signal switch” (P.2-40).

21. Vehicle ahead detection indica-
tor

This indicator shows the status of the
following systems, if the vehicle is equipped
with them.

.

Forward Emergency Braking (FEB) with

pedestrian detection system

.

Predictive Forward Collision Warning

(PFCW)

Instruments and controls

2-25

2-26

Instruments and controls

.

Distance Control Assist (DCA)

For more details, see “Forward Emergency
Braking (FEB) with pedestrian detection”
(P.5-95), “Predictive Forward Collision
Warning (PFCW)” (P.5-103) or “Distance
Control Assist (DCA)” (P.5-84).
The figure and color of these indicators will
change depending on the conditions of the
above systems.

22. LDW indicator

This indicator shows the status of the
following systems, if the vehicle is equipped
with them.

.

Lane Departure Warning (LDW)

.

Lane Departure Prevention (LDP)

For more details, see “Lane Departure
Warning (LDW)/Lane Departure Prevention
(LDP)” (P.5-22).
The figure and color of these indicators will
change depending on the conditions of the
above systems.

23. BSW indicator

This indicator shows the status of the
following systems, if the vehicle is equipped
with them.

.

Blind Spot Warning (BSW)

.

Blind Spot Intervention

®

(BSI)

For more details, see “Blind Spot Warning

(BSW)” (P.5-31) or “Blind Spot Intervention

®

(BSI)” (P.5-41).
The figure and color of these indicators will
change depending on the conditions of the
above systems.

24. Malfunction

This warning appears when one or more of
the following systems (if so equipped) is not
functioning properly:

.

Forward Emergency Braking (FEB) with

pedestrian detection system

.

Predictive Forward Collision Warning

(PFCW)

.

Lane Departure Warning (LDW)

.

Lane Departure Prevention (LDP)

.

Blind Spot Warning (BSW)

.

Blind Spot Intervention

®

(BSI)

.

Back-up Collision Intervention (BCI)

.

Distance Control Assist (DCA)

If one or more of these warning appears,
have the system checked. It is recommended
you visit an INFINITI retailer for this service.

25. Wiper Mode Guidance

This indicator shows the wiper and washer
switch position.
The selected position is illuminated in orange
when the wiper switch position is changed.

26. Lights Mode Guidance

This indicator shows the headlight switch
position.
The selected position is illuminated in orange
when the headlight switch position is chan-
ged.

27. Intelligent Cruise Control (ICC)
indicators (if so equipped)

These indicators show the Intelligent Cruise
Control (ICC) system status. For additional
information, refer to “Intelligent Cruise Con-
trol (ICC)” (P.5-64).

28. Stop vehicle and Apply parking
brake (if so equipped)

This warning may appear when the battery
charge is low.
Park the vehicle as soon as possible. It is
recommended that you visit an INFINITI
retailer.

29. Cruise indicator

Models without Intelligent Cruise Control
(ICC) system:

This indicator shows the cruise control
system status. The status is shown by the
color.
See “Cruise control” (P.5-62) for details.

Models with Intelligent Cruise Control (ICC)
system:

This indicator shows the conventional (fixed
speed) cruise control mode status. The
status is shown by the color.
See “Conventional (fixed speed) cruise con-
trol mode display and indicators” (P.5-81)
for details.

30. Not Available: High Camera
Temp (if so equipped)

This message appears when the Lane De-
parture Warning (LDW)/Lane Departure
Prevention (LDP) (if so equipped)/Blind Spot
Intervention

®

(if so equipped) systems be-

come unavailable because a camera detects
an interior temperature of more than 104°F
(40°C).
For additional information, refer to “Lane
Departure Warning (LDW)/Lane Departure
Prevention (LDP)” (P.5-22) or “Blind Spot
Intervention

®

(BSI)” (P.5-41).

31. Unavailable: Side Radar Ob-
struction (if so equipped)

This message appears when the Blind Spot
Warning (BSW)/Blind Spot Intervention

®

(BSI) (if so equipped)/Back-up Collision
Intervention (BCI) systems become unavail-
able because a radar blockage is detected.

For additional information, refer to “Blind
Spot Warning (BSW)” (P.5-31), “Blind Spot
Intervention

®

(BSI)” (P.5-41) or “Back-up

Collision Intervention (BCI)” (P.5-53).

32. Unavailable: High Accelerator
Temperature

This message appears when the Back-up
Collision Intervention (BCI) system and/or
the Distance Control Assist (DCA) system
becomes unavailable because of an interior
temperature greater than approximately
104°F (40°C). For additional information,
refer to “Back-up Collision Intervention
(BCI)” (P.5-53) or “Distance Control Assist
(DCA)” (P.5-84).

33. Not Available: Front Radar
Blocked

This message appears when the sensor area
of the front bumper is covered with dirt or is
obstructed, making it impossible to detect a
vehicle ahead.
The following systems will be automatically
canceled.

.

Intelligent Cruise Control (ICC) system (if

so equipped)

.

Distance Control Assist (DCA) system (if

so equipped)

.

Forward Emergency Braking (FEB) with

pedestrian detection system

.

Predictive Forward Collision Warning

(PFCW) system

For more details, see “Intelligent Cruise
Control (ICC)” (P.5-64), “Distance Control
Assist (DCA)” (P.5-84), “Forward Emer-
gency Braking (FEB) with pedestrian detec-
tion” (P.5-95) or “Predictive Forward
Collision Warning (PFCW)” (P.5-103).

34. Shipping Mode On Push Sto-
rage Fuse (if so equipped)

This warning may appear if the extended
storage fuse switch is not pushed in
(switched on). When this warning appears,
push in (switch on) the extended storage
fuse switch to turn off the warning. For
more information, see “Extended storage
fuse switch” (P.8-20).

35. Headlight System Error

This warning appears if the LED headlights
are malfunctioning. It is recommended you
have the system checked by an INFINITI
retailer.

Instruments and controls

2-27

2-28

Instruments and controls

36. Lane Departure Prevention
(LDP)/Blind Spot Intervention

®

(BSI)/Distance Control Assist
(DCA) ON indicator (if so equipped)

This indicator appears when one or more of
the following systems (if so equipped) is
activated.

.

Lane Departure Prevention (LDP)

.

Blind Spot Intervention

®

(BSI)

.

Distance Control Assist (DCA)

For more details, see “Lane Departure
Warning (LDW)/Lane Departure Prevention
(LDP)” (P.5-22), “Blind Spot Intervention

®

(BSI)” (P.5-41), or “Distance Control Assist
(DCA)” (P.5-84).

37. Not Available: Poor Road Con-
ditions (if so equipped)

This warning may appear when the Blind
Spot Intervention

®

(BSI), the Lane Depar-

ture Prevention (LDP), Distance Control
Assist (DCA) or the Intelligent Cruise Control
(ICC) system is engaged.
Under the following conditions, the BSI,
LDP, DCA or the ICC system is automatically
canceled:

.

When the Vehicle Dynamic Control

(VDC) operates

.

When a wheel slips

The above system cannot be used in some
situations. (VDC operates and a wheel slips.)

38. Currently unavailable (if so
equipped)

This message appears and the Blind Spot
Intervention

®

(BSI) system, the Lane Depar-

ture Prevention (LDP) system, Intelligent
Cruise Control (ICC) and Distance Control
Assist (DCA) system will be turned off
automatically under the following condi-
tions:

.

When the VDC system is turned off.

.

When the SNOW mode is selected.

.

When the 4WD shift switch is in the 4H

or 4L position. (4WD models).

“Vehicle Dynamic Control (VDC) system”
(P.5-125), “SNOW mode” (P.5-122),
“INFINITI all-mode 4WD

®

system” (P.5-

114), “Blind Spot Intervention

®

(BSI)” (P.5-

41), “Lane Departure Warning (LDW)/Lane
Departure Prevention (LDP)” (P.5-22), “In-
telligent Cruise Control (ICC)” (P.5-64) and
“Distance Control Assist (DCA)” (P.5-84).

39. Automatic Transmission (AT)
position indicator

This indicator shows the transmission shift
position.

See “Automatic transmission” (P.5-18) for
further details.

40. Rear Door Alert is activated

When the rear door alert system is enabled,
this message appears when the rear door
alert system is active and can remind the
driver to check the rear seat.

NOTE:

This system is disabled until a driver enables
it using the rear door alert switch.

For more details, see “Rear door alert” (P.2-
54).

41. Check Rear Seat for all articles

When the rear door alert system is enabled,
this message appears when the vehicle
comes to a complete stop, the shift lever is
moved from the D (Drive) or R (Reverse)
position to P (Park) position, and the driver
exits the vehicle. This message alerts the
driver, after a period of time, to check for
items in the rear seat after the audible alert
has been provided.

NOTE:

This rear door alert system is disabled until
a driver enables it using the rear door alert
switch.

For more details, see “Rear door alert” (P.2-
54).

42. Rear Seat Belt warning

This rear seat belt warning appears after the
ignition switch is pushed to the ON position.
If any of the rear passenger’s seat belts is
not fastened, the seat icon illuminates in red
to show which seat belt is not fastened. The
seat icon illuminates in red until the corre-
sponding rear passenger’s seat belt is fas-
tened. The warning will automatically turn
off after approximately 65 seconds. If so
equipped, the seat icon will turn gray if the
seat is occupied and the passenger is
buckled. If a rear passenger seat belt is
fastened then unfastened at a vehicle speed
less than approximately 10 MPH (15 km/h),
the seat icon will illuminate. When the
vehicle speed exceeds approximately 10
MPH (15 km/h), the seat icon will blink and
the chime will sound. The warning will turn
off when a rear passenger seat belt is
fastened or automatically turn off approxi-
mately 65 seconds after the seat belt is
unfastened. For precautions on seat belt
usage, see “Seat belts” (P.1-18).
The display of the rear seat belt warning
varies depending on the number of seats.

Instruments and controls

2-29

2-30

Instruments and controls

WAC0224X

WAC0142X

TRIP COMPUTER

The trip computer switch is located on the
left side of the steering wheel. To operate
the trip computer, push the switch.
Each time the left or right side of the
switch is pushed, the display will change.
The display item for trip computer is chan-
ged on the lower display. For details, see the
INFINITI InTouch

TM

Owner’s Manual.

1. Home

The Home mode shows the following in-
formation.

.

Vehicle speed

.

Navigation (if so equipped)

.

Audio

2. Audio

The audio mode shows the status of audio
information.
For more details, see the INFINITI In-
Touch

TM

Owner’s Manual.

3. Compass

This display indicates the heading direction
of the vehicle.

4. Navigation

When the route guidance is set in the
navigation system, this item shows the
navigation route information.
For more details, see the INFINITI In-
Touch

TM

Owner’s Manual.

5. Vehicle speed (MPH or km/h)

The vehicle speed mode shows the current
vehicle speed and the average vehicle speed
since the last reset.
Resetting is done by pushing the left or right
side of the

switch for longer than 1

second.

Average vehicle speed:

The average vehicle speed display is updated
every 30 seconds. The first 30 seconds after

a reset, the display shows “———”.

6. Elapsed time and trip odometer
(mile or km)

Elapsed time:

The elapsed time mode shows the time since
the last reset. The displayed time can be
reset by pushing the left or right side of the

switch for longer than 1 second. (The

trip odometer is also reset at the same time.)

Trip odometer:

The trip odometer mode shows the total
distance the vehicle has been driven since
the last reset. Resetting is done by pushing
the left or right side of the

switch for

longer than 1 second. (The elapsed time is
also reset at the same time.)

7. Current fuel consumption and
average fuel consumption (MPG, l
(liter)/100 km or km/l)

Current fuel consumption:

The current fuel consumption mode shows
the current fuel consumption.

Average fuel consumption:

The average fuel consumption mode shows
the average fuel consumption since the last
reset. Resetting is done by pushing the left
or right side of the

switch for longer

Instruments and controls

2-31

2-32

Instruments and controls

than 1 second.
The average fuel consumption is also reset
on the lower display. See the INFINITI
InTouch

TM

Owner’s Manual.

The display is updated every 30 seconds. At
about the first 1/3 mile (500 m) after a
reset, the display shows “——”.

8. Intelligent Cruise Control (ICC)
system (if so equipped)

This mode shows the operating condition for
the Intelligent Cruise Control (ICC) system.
(See “Intelligent Cruise Control (ICC)” (P.5-
64).)

NOTE:

If the ICC system is activated when [Cruise
Screen Transition] is set to ON in the
settings menu on the lower display, this
screen is automatically displayed. (See the
INFINITI InTouch

TM

Owner’s Manual.)

9. Driving aids (if so equipped)

The driving aids mode shows the operating
condition for the following systems, if the
vehicle is equipped with them.

.

Forward Emergency Braking (FEB) with

pedestrian detection system

.

Predictive Forward Collision Warning

(PFCW)

.

Lane Departure Warning (LDW)

.

Lane Departure Prevention (LDP)

.

Blind Spot Warning (BSW)

.

Blind Spot Intervention

®

(BSI)

.

Distance Control Assist (DCA)

For more details, see “Forward Emergency
Braking (FEB) with pedestrian detection”
(P.5-95), “Predictive Forward Collision
Warning (PFCW)” (P.5-103), “Lane Depar-
ture Warning (LDW)/Lane Departure Pre-
vention (LDP)” (P.5-22), “Blind Spot
Warning (BSW)” (P.5-31), “Blind Spot Inter-
vention

®

(BSI)” (P.5-41), or “Distance Con-

trol Assist (DCA)” (P.5-84).

10. Tire pressures

The tire pressure mode shows the pressure
of all four tires while the vehicle is driven.
When the “Tire Pressure Low Add Air”
warning appears, the display can be
switched to the tire pressure mode by
pushing the left or right side of the
switch.
The tire pressure unit can be changed using
the settings menu on the lower display. (See
the INFINITI InTouch

TM

Owner’s Manual.)

NOTE:

After the ignition switch is placed in the ON
position, it may take a period of time for the
tire pressure to be displayed while the

vehicle is driven. Depending on the radio
wave circumstance, tire pressure may not
correctly be displayed.

WAC0225X

11. Auxiliary gauges

The auxiliary gauges consist of the battery
voltage gauge and the engine oil pressure
gauge.

The engine oil pressure gauge indicates
current engine oil pressure. (See “En-
gine oil pressure gauge” (P.2-9).)
The battery voltage gauge indicates
current battery voltage. (See “Volt-
meter” (P.2-10).)

WAC0226X

CLOCK AND OUTSIDE AIR TEM-
PERATURE

The clock

and outside air temperature

are displayed on the upper side of the vehicle
information display.

Clock

The clock can be adjusted on the lower
display. See the INFINITI InTouch

TM

Own-

er’s Manual.

Outside air temperature (°F or °C)

The outside air temperature is displayed in °F
or °C in the range of −40 to 140°F (−40 to
60°C).

The outside temperature sensor is located in
front of the radiator. The sensor may be
affected by road or engine heat, wind
directions and other driving conditions. The
display may differ from the actual outside
temperature or the temperature displayed
on various signs or billboards.

Instruments and controls

2-33

2-34

Instruments and controls

SIC2133

Your vehicle has two types of security
systems, as follows:

.

Vehicle security system

.

INFINITI Vehicle Immobilizer System

The security condition will be shown by the
security indicator light.

VEHICLE SECURITY SYSTEM

The vehicle security system provides visual
and audio alarm signals if someone opens
the doors, hood, or liftgate when the system
is armed. It is not, however, a motion
detection type system that activates when
a vehicle is moved or when a vibration
occurs.
The system helps deter vehicle theft but
cannot prevent it, nor can it prevent the
theft of interior or exterior vehicle compo-
nents in all situations. Always secure your
vehicle even if parking for a brief period.
Never leave your Intelligent Key(s) in the
vehicle, and always lock it when unattended.
Be aware of your surroundings, and park in
secure, well-lit areas whenever possible.
Many devices offering additional protection,
such as component locks, identification
markers, and tracking systems, are available
at auto supply stores and specialty shops.
Your INFINITI retailer may also offer such
equipment. Check with your insurance com-
pany to see if you may be eligible for
discounts for various theft protection fea-
tures.

SIC2045

How to arm the vehicle security
system

1. Close all windows.

The system can be armed even if the
windows are open.

2. Push the ignition switch to the OFF

position.

3. Remove the Intelligent Key from the

vehicle.

4. Close all doors, hood and liftgate. Lock

all doors. The doors can be locked with
the Intelligent Key, door handle request
switch, power door lock switch or me-
chanical key.

SECURITY SYSTEMS