Infiniti QX80 (2021 year). Manual in english — page 8

5. Confirm that the security indicator light

comes on. The security indicator light
stays on for about 30 seconds. The
vehicle security system is now pre-
armed. After about 30 seconds the
vehicle security system automatically
shifts into the armed phase. The security
light begins to flash once every approxi-
mately 3 seconds. If, during this 30-
second pre-arm time period, the door is
unlocked, or the ignition switch is pushed
to ACC or ON, the system will not arm.

Even when the driver and/or passengers
are in the vehicle, the system will activate
with all doors, hood, and liftgate locked
with the ignition switch in the LOCK
position. When pushing the ignition switch
to the ACC or ON position, the system will
be released.

Vehicle security system activation

The vehicle security system will give the
following alarm:

.

The headlights blink and the horn sounds

intermittently.

.

The alarm automatically turns off after

approximately 50 seconds. However, the
alarm reactivates if the vehicle is tam-
pered with again.

The alarm is activated by:

.

Unlocking the door or opening the lift-

gate without using the button on the
Intelligent Key, the door handle request
switch or the mechanical key. (Even if the
door is opened by releasing the door
inside lock knob, the alarm will activate.)

.

Opening the hood.

How to stop an activated alarm

The alarm will stop when a door is unlocked
by pushing the unlock button on the Intelli-
gent Key, the door handle request switch or
using the mechanical key, or when the
ignition switch is pushed to the ACC or ON
position.

If the system does not operate as described
above, it is recommended you have it
checked by an INFINITI retailer.

INFINITI VEHICLE IMMOBILIZER
SYSTEM

The INFINITI Vehicle Immobilizer System
will not allow the engine to start without
the use of the registered Intelligent Key.

Never leave these keys in the vehicle.

FCC Notice:

For USA:

This device complies with Part 15 of the
FCC Rules. Operation is subject to the

following two conditions: (1) This device
may not cause harmful interference, and (2)
this device must accept any interference
received, including interference that may
cause undesired operation.

NOTE:

Changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s authority
to operate the equipment.

For Canada:

This device complies with Industry Canada
licence-exempt RSS standard(s). Operation
is subject to the following two conditions:
(1) this device may not cause interference,
and (2) this device must accept any inter-
ference, including interference that may
cause undesired operation of the device.

Instruments and controls

2-35

2-36

Instruments and controls

SIC2045

Security indicator light

The security indicator light is located on the
meter panel. It indicates the status of the
INFINITI Vehicle Immobilizer System.
The light blinks after the ignition switch was
in the ACC, OFF and LOCK position. This
function indicates the security systems
equipped on the vehicle are operational.
If the INFINITI Vehicle Immobilizer System is
malfunctioning, this light will remain on
while the ignition switch is in the ON
position.

If the light still remains on and/or the
engine will not start, seek service for the
INFINITI Vehicle Immobilizer System as

soon as possible. Please bring all registered
keys that you have. It is recommended you
visit an INFINITI retailer for this service.

WARNING

In freezing temperatures the washer
solution may freeze on the window and
obscure your vision which may lead to an
accident. Warm the window with the
defroster before you wash the window.

CAUTION

.

Do not operate the washer continu-
ously for more than 30 seconds.

.

Do not operate the washer if the
reservoir tank is empty.

.

Do not fill the window washer re-
servoir tank with washer fluid con-
centrates at full strength. Some
methyl alcohol based washer fluid
concentrates may permanently stain
the grille if spilled while filling the
window washer reservoir tank.

.

Pre-mix washer fluid concentrates
with water to the manufacturer’s
recommended levels before pouring
the fluid into the window washer
reservoir tank. Do not use the win-
dow washer reservoir tank to mix the
washer fluid concentrate and water.

WIPER AND WASHER SWITCH

If the windshield wiper operation is inter-
rupted by snow or ice, the wiper may stop
moving to protect its motor. If this occurs,
turn the wiper switch to the OFF position
and remove the snow or ice that is on and
around the wiper arms. In approximately 1
minute, turn the switch on again to operate
the wiper.

JVI0738X

The windshield wiper and washer operates
when the ignition switch is in the ON
position.
Push the lever down to operate the wiper at
the following speed:

AUTO — operates the rain-sensing
auto wiper system. (See “Rain-sensing
auto wiper system” (P.2-38).)
LO — continuous low speed operation
HI — continuous high speed operation
MIST — one sweep operation of the
wiper

WASHER OPERATION

To operate the washer, pull the lever toward
the back of the vehicle

until the desired

amount of washer fluid is spread on the
windshield. The wiper will automatically
operate several times.
The headlight washer (if so equipped) will
also operate with operation of the wind-
shield washer. (See “Headlight washer” (P.2-
45).)

Wiper drip wipe system:

The wiper will also operate once about 3
seconds after the washer and wiper are
operated. This operation is to wipe washer
fluid that has dripped on the windshield.

Instruments and controls

2-37

2-38

Instruments and controls

JVI0739X

RAIN-SENSING AUTO WIPER
SYSTEM

The rain-sensing auto wiper system can
automatically turn on the wipers and adjust
the wiper speed depending on the rainfall
and the vehicle speed by using the rain
sensor located on the upper part of the
windshield.
To set the rain-sensing auto wiper system,
push the lever down to the AUTO position

. The wiper will sweep once while the

ignition switch is in the ON position.
The rain sensor sensitivity level can be
adjusted by turning the knob toward the
front

(High) or toward the rear

(Low).

.

High — High sensitive operation

.

Low — Low sensitive operation

To turn the rain-sensing auto wiper system
off, push up the lever to the OFF position, or
pull down the lever to the LO or HI position.

CAUTION

Do not touch the rain sensor and around
it when the wiper switch is in the AUTO
position and the ignition switch is in the
ON position. The wipers may operate
unexpectedly and cause to an injury or
may damage a wiper.

.

The rain-sensing auto wipers are in-

tended for use during rain. If the switch
is left in the AUTO position, the wipers
may operate unexpectedly when dirt,
fingerprints, oil film or insects are stuck
on or around the sensor. The wipers may
also operate when exhaust gas or
moisture affect the rain sensor.

.

The rain-sensing auto wipers may not

operate if rain does not hit the rain
sensor even if it is raining.

.

When the windshield glass is coated

with water repellent, the speed of the
rain-sensing auto wipers may be higher
even though the amount of the rainfall is
small.

.

Be sure to turn off the rain-sensing auto

wiper system when you use a car wash.

.

When the ignition switch is in the ON

position and the vehicle speed is below
approximately 5 MPH (8 km/h) with
the shift lever in the N (Neutral) posi-
tion, the rain-sensing auto wipers will
not operate.

.

Using genuine wiper blades is recom-

mended for proper operation of the
rain-sensing auto wiper system. (See
“Windshield wiper blades” (P.8-15) for
wiper blade replacement.)

JVI0972X

REAR WINDOW WIPER AND
WASHER OPERATION

If the rear window wiper operation is
interrupted by snow etc., the wiper may
stop moving to protect its motor. If this
occurs, turn the wiper switch to OFF and
remove the snow etc. on and around the
wiper arms. After about 1 minute, turn the
switch ON again to operate the wiper.

The rear window wiper and washer operate
when the ignition switch is in the ON
position.
Turn the switch clockwise from the OFF
position to operate the wiper.

Intermittent (INT) — intermittent op-
eration (not adjustable)
Low (ON) — continuous low speed
operation

Push the switch forward

to operate the

washer. Then the wiper will also operate
several times.

JVI1777X

REAR WINDOW AND OUTSIDE
MIRROR DEFROSTER

To defog/defrost the rear window glass and
outside mirrors, start the engine and push
the switch

on. The indicator light

will

come on. Push the switch again to turn the
defroster off.
It will automatically turn off in approxi-
mately 15 minutes.

CAUTION

When cleaning the inner side of the rear
window, be careful not to scratch or

Instruments and controls

2-39

REAR WINDOW AND OUTSIDE
MIRROR DEFROSTER SWITCH

2-40

Instruments and controls

damage the rear window defroster.

SIC3267

HEADLIGHT SWITCH

Lighting

Turn the switch to the

position:

The front parking, side marker, tail,
license plate and instrument lights will
come on.
Turn the switch to the

position:

Headlights will come on and all the
other lights remain on.

SIC3268

Autolight system

The autolight system allows the headlights
to be set so they turn on and off auto-
matically.
To set the autolight system:
1. Make sure the headlight switch is in the

AUTO position

.

2. Push the ignition switch to the ON

position.

3. The autolight system automatically turns

the headlights on and off.

To turn the autolight system off, turn the
switch to the OFF,

or

position.

The autolight system can turn on the head-

HEADLIGHT AND TURN SIGNAL SWITCH

lights automatically when it is dark and turn
off the headlights when it is light.
For US models: The headlights will also be
turned on automatically at twilight or in
rainy weather (when the windshield wiper is
operated continuously).
If the ignition switch is pushed to the OFF
position and one of the doors is opened and
this condition is continued, the headlights
remain on for 5 minutes.

Automatic headlights off delay:

You can keep the headlights on for up to 180
seconds after you push the ignition switch to
OFF and open any door then close all the
doors.
You can adjust the period of the automatic
headlights off delay from 0 seconds (OFF)
to 180 seconds. The factory default setting
is 45 seconds.
For automatic headlights off delay setting,
see INFINITI InTouch

TM

Owner’s Manual.

SIC3784A

Be sure not to put anything on top of the
photo sensor

located on the top of the

instrument panel. The photo sensor controls
the autolight; if it is covered, the photo
sensor reacts as if it is dark and the head-
lights will illuminate.

SIC3269

To select the low beam, put the lever in
the neutral position as shown.
To select the high beam, push the lever
forward while the switch is in the
position. Pull it back to select the low
beam.
Pulling the lever toward you will flash
the headlight high beam even when the
headlight switch is in the OFF position.

Headlight beam select

High beam assist

The high beam assist system will operate
when the vehicle is driven at speeds of
approximately 22 MPH (35 km/h) and

Instruments and controls

2-41

2-42

Instruments and controls

above. If an oncoming vehicle or leading
vehicle appears in front of your vehicle when
the headlight high beam is on, the headlight
will be switched to the low beam automa-
tically.

Precautions on high beam assist:

WARNING

.

The high beam assist system is a
convenience but it is not a substitute
for safe driving operation. The driver
should remain alert at all times,
ensure safe driving practices and
switch the high beams and low beam
manually when necessary.

.

The high beam or low beam may not
switch automatically under the fol-
lowing conditions. Switch the high
beam and low beam manually.

— During bad weather (rain, fog,

snow, wind, etc.).

— When a light source similar to a

headlight or tail light is in the
vicinity of the vehicle.

— When the headlights of the on-

coming vehicle or the leading
vehicle are turned off, when the
color of the light is affected due to
foreign materials on the lights, or

when the light beam is out of
position.

— When there is a sudden, contin-

uous change in brightness.

— When driving on a road that

passes over rolling hills, or a road
that has level differences.

— When driving on a road with

many curves.

— When a sign or mirror-like sur-

face is reflecting intense light
towards the front of the vehicle.

— When the container, etc. being

towed by a leading vehicle is
reflecting intense light.

— When a headlight on your vehicle

is damaged or dirty.

— When the vehicle is leaning at an

angle due to a punctured tire,
being towed, etc.

.

The timing of switching the low beam
and high beam may change under the
following situations.

— The brightness of the headlights

of the oncoming vehicle or leading
vehicle.

— The movement and direction of

the oncoming vehicle and the

leading vehicle.

— When only one light on the on-

coming vehicle or the leading
vehicle is illuminated.

— When the oncoming vehicle or the

leading vehicle is a two-wheeled
vehicle.

— Road conditions (incline, curve,

the road surface, etc.).

— The number of passengers and

the amount of luggage.

JVI0686X

High beam assist operations:

To activate the high beam assist system,
turn the headlight switch to the AUTO
position

and push the lever forward

(high beam position). The high beam assist
indicator light in the meter will illuminate
while the headlights are turned on.
If the high beam assist indicator light does
not illuminate in the above condition, it may
indicate that the system is not functioning
properly. It is recommended you have the
system checked by an INFINITI retailer.
When the vehicle speed lowers to less than
approximately 17 MPH (27 km/h), the head-
light remains the low beam.

To turn off the high beam assist system, turn
the headlight switch to the

position or

select the low beam position by placing the
lever in the neutral position.

JVI1740X

Ambient image sensor maintenance:

The ambient image sensor

for the high

beam assist system is located as shown. To
keep the proper operation of the high beam
assist system and prevent a system mal-
function, be sure to observe the following:

.

Always keep the windshield clean.

.

Do not attach a sticker (including trans-

parent material) or install an accessory
near the ambient image sensor.

.

Do not strike or damage the areas around

the ambient image sensor. Do not touch
the sensor lens that is located on the
ambient image sensor.

If the ambient image sensor is damaged due
to an accident, it is recommended you visit

Instruments and controls

2-43

2-44

Instruments and controls

an INFINITI retailer for this service.

Battery saver system

A chime will sound when the driver side door
is opened with the light switch in the

or

position and the ignition switch in the

OFF or LOCK position.
When the headlight switch is in the

or

position while the ignition switch is in

the ON position, the lights will automatically
turn off after a period of time when the
ignition switch has been pushed to the OFF
position.
When the headlight switch remains in the

or

position after the lights auto-

matically turn off, the lights will turn on
when the ignition switch is pushed to the ON
position.

CAUTION

.

When you turn on the headlight
switch again after the lights auto-
matically turn off, the lights will not
turn off automatically. Be sure to
turn the light switch to the OFF
position when you leave the vehicle
for extended periods of time, other-
wise the battery will be discharged.

.

Never leave the light switch on when
the engine is not running for ex-
tended periods of time even if the
headlights turn off automatically.

SIC2275

Headlight aiming control (if so
equipped)

Depending on the number of occupants in
the vehicle and the load it is carrying, the
headlight axis may be higher than desired. If
the vehicle is traveling on a hilly road, the
headlights may directly hit the rearview
mirror of the vehicle ahead or the windshield
of the oncoming vehicle. The light axis can be
lowered with the operation of the switch.
The larger the number designated on the
switch, the lower the axis.
When traveling with no heavy load or on a
flat road, select position 0.

Daytime running light system

The daytime running lights automatically
illuminate when the engine is started with
the parking brake released. The daytime
running lights operate with the headlight
switch in the OFF position or in the
position. Turn the headlight switch to the

position for full illumination when driv-

ing at night.
If the parking brake is applied before the
engine is started, the daytime running lights
do not illuminate. The daytime running lights
illuminate once the parking brake is released.
The daytime running lights will remain on
until the ignition switch is pushed to the OFF
position.

WARNING

When the daytime running light system
is active, tail lights on your vehicle are
not on. It is necessary at dusk to turn on
your headlights. Failure to do so could
cause an accident injuring yourself and
others.

Adaptive Front lighting System
(AFS) (if so equipped)

The Adaptive Front lighting System (AFS)
will automatically adjust the headlights (low
beam) toward the turning direction to
improve the driver’s view. When the head-
light switch is ON and the driver operates
the steering wheel in a turn, the AFS system
will be activated.
The AFS will operate:

.

when the headlight switch is ON.

.

when the shift lever is in any position

other than P (Park) or R (Reverse).

.

when the vehicle is driven at above 3

MPH (5 km/h) for the left-side head-
light. Note that the right-side low beam
headlight will swivel but the left-side
headlight will not swivel when the vehicle
is below 3 MPH (5 km/h) and the
steering wheel is turned.

AFS will also adjust the headlight to a proper
axis automatically, depending on the number
of occupants in the vehicle, the load the
vehicle is carrying and the road conditions.
If the AFS OFF indicator light blinks after
the ignition switch has been pushed to the
ON position, this may indicate that the AFS
is not functioning properly. Have the system
checked. It is recommended you visit an
INFINITI retailer for this service. When the

engine is started, the headlights will vibrate
to check the system condition. This is not a
malfunction.

HEADLIGHT WASHER (if so
equipped)

The headlight washer operates when the
headlight is on and the ignition switch is in
the ON position.
Pull the windshield washer switch toward
you. The headlight washer operates with the
windshield washer operation. This operation
activates once each time either the ignition
switch or the headlight switch is turned off
and on.
After the first operation, the headlight
washer operates once at every fifth opera-
tion of the windshield washer.

CAUTION

.

Do not operate the washer continu-
ously for longer than 30 seconds.

.

Do not operate the headlight washer
if the window washer fluid reservoir
is empty.

Instruments and controls

2-45

2-46

Instruments and controls

SIC4378

INSTRUMENT BRIGHTNESS
CONTROL

The instrument brightness control switch
(upper

and lower

) can be operated when

the ignition switch is in the ON position.

WAC0256X

When the instrument brightness control
switch is operated, the vehicle information
display switches to the brightness adjust-
ment mode.
Push the upper switch

to brighten the

meter panel lights and instrument panel
lights.
Push the lower switch

to dim the lights.

If the bar reaches the maximum or minimum
brightness, a chime will sound.
The vehicle information display returns to
the normal display when the instrument
brightness control switch is not operated
for more than 5 seconds.

SIC3271

TURN SIGNAL SWITCH

Turn signal

Move the lever up or down to signal the
turning direction. When the turn is com-
pleted, the turn signals cancel automatically.

Lane change signal

.

Move the lever up or down until the turn

signal begins to flash, but the lever does
not latch, to signal a lane change. Hold
the lever until the lane change is com-
pleted.

.

Move the lever up or down until the turn

signal begins to flash, but the lever does
not latch, and release the lever. The turn

signal will automatically flash three
times.

Choose the appropriate method to signal a
lane change based on road and traffic
conditions.

SIC3272

FOG LIGHT SWITCH

To turn the fog lights on, turn the headlight
switch to the

position, then turn the

switch to the

position. To turn them off,

turn the switch to the OFF position.
The headlights must be on with the low
beams selected for the fog lights to operate.
The fog lights automatically turn off when
the high beam headlights are selected.

JVI0395X

The heated steering wheel system is de-
signed to operate only when the surface
temperature of the steering wheel is below
68°F (20°C).
Push the heated steering wheel switch to
warm the steering wheel after the engine
starts. The indicator light

on the switch

will illuminate.
If the surface temperature of the steering
wheel is below 68°F (20°C), the system will
heat the steering wheel and cycle off and on
to maintain a temperature above 68°F
(20°C). The indicator light will remain on as
long as the system is on.
Push the switch again to turn the heated
steering wheel system off manually. The

Instruments and controls

2-47

HEATED STEERING WHEEL

2-48

Instruments and controls

indicator light will turn off.

NOTE:

If the surface temperature of the steering
wheel is above 68°F (20°C) when the switch
is turned on, the system will not heat the
steering wheel. This is not a malfunction.

SIC4444

To sound the horn, push the center pad area
of the steering wheel.

WARNING

Do not disassemble the horn. Doing so
could affect proper operation of the
supplemental front air bag system. Tam-
pering with the supplemental front air
bag system may result in serious perso-
nal injury.

WARNING

Do not use or allow occupants to use the
seat heater if you or the occupants
cannot monitor elevated seat tempera-
tures or have an inability to feel pain in
body parts that contact the seat. Use of
the seat heater by such people could
result in serious injury.

CAUTION

.

The battery could run down if the
seat heater is operated while the
engine is not running.

.

Do not use the seat heater for
extended periods or when no one is
using the seat.

.

Do not put anything on the seat
which insulates heat, such as a blan-
ket, cushion, seat cover, etc. Other-
w i s e , t h e s e a t m a y b e c o m e
overheated.

.

Do not place anything hard or heavy
on the seat or pierce it with a pin or
similar object. This may result in
damage to the heater.

HORN

HEATED SEATS

.

Any liquid spilled on the heated seat
should be removed immediately with
a dry cloth.

.

When cleaning the seat, never use
gasoline, thinner, or any similar ma-
terials.

.

If any malfunctions are found or the
heated seat does not operate, turn
the switch off and have the system
checked. It is recommended you visit
an INFINITI retailer for this service.

JVR0600X

FRONT

The front seats can be warmed by built-in
heaters. The switches located on the instru-
ment panel can be operated independently
of each other.
1. Start the engine.
2. Push the heated seat switch and select

the desired heat range.

.

For high heat, push the switch once.

.

For medium heat, push the switch

twice.

.

For low heat, push the switch three

times.

.

The indicator light

on the switch will

illuminate depending on the heat level

when the heater is on.

3. To turn off the heater, push the heated

seat switch until the indicator light turns
off.
The heater is controlled by a control
module, automatically turning the heater
on and off.
The indicator light will remain on as long
as the switch is on.
When the vehicle’s interior is warmed, or
before you leave the vehicle, be sure to
turn off the seat heater.

Instruments and controls

2-49

2-50

Instruments and controls

SIC2770

REAR (if so equipped)

The 2nd row outboard seats are warmed by
built-in heaters. The switches located on the
back side of the center console can be
operated independently of each other.
1. Start the engine.
2. Select heat range.

For high heat, push the HI (High) side

of the switch.

For low heat, push the LO (Low) side

of the switch.
The indicator light in the switch

will

illuminate when the heater is on.

3. To turn off the heater, return the switch

to the level position. Make sure the
indicator light goes off.
The heater is controlled by a thermostat,
automatically turning the heater on and
off. The indicator light will remain on as
long as the switch is on.
When the vehicle’s interior is warmed, or
before you leave the vehicle, be sure to
turn off the switch.

WARNING

Do not use or allow occupants to use the
climate controlled seats if you or the
occupants cannot monitor seat tem-
peratures or have an inability to feel
pain in body parts that contact with the
seat. Use of the climate controlled seats
by such people could result in serious
injury.

CAUTION

.

The battery could run down if the
climate controlled seat is operated
while the engine is not running.

.

Do not use the climate controlled seat
for extended periods or when no one
is using the seat.

.

Do not put anything on the seat
which insulates heat, such as a blan-
ket, cushion, seat cover, etc. Other-
w i s e , t h e s e a t m a y b e c o m e
overheated.

.

Do not place anything hard or heavy
on the seat or pierce it with a pin or
similar object. This may result in
damage to the climate controlled

CLIMATE CONTROLLED SEATS
(if so equipped)