Infiniti EX35. Manual — part 836
COWL TOP
EXT-23
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
Removal and Installation
INFOID:0000000003134290
REMOVAL
1.
Fully open hood assembly.
2.
Remove front wiper arm (LH/RH) from vehicle. Refer to
WW-106, "Removal and Installation"
3.
Remove battery cover and brake master cylinder cover.
4.
Remove cowl top cover seal (LH/RH).
5.
Remove hoodledge cover mounting clips and then remove hoodledge cover (LH/RH).
6.
Remove front fender cover (1) fixing clips (LH/RH).
7.
Remove cowl top seal fixing clips with remover tool, and then remove cowl top seal.
8.
Remove cowl top cover fixing clips.
9.
Pull up plastic pawl (A) to remove cowl top cover RH (1) as
shown in the figure.
10. Push plastic pawl (A) as shown by the arrow in the figure to
remove cowl top cover LH (1).
INSTALLATION
Note the following, and install in the reverse order of removal.
: Clip
JMKIA2237ZZ
JMKIA2158ZZ
JMKIA2159ZZ
EXT-24
< ON-VEHICLE REPAIR >
COWL TOP
• Install cowl top cover LH (1) with (A) [pin from front windshield
glass(2)] aligned with concave part.
• Slide the pawl while aligning with the concave part of (C).
• Engage the joint of plastic pawl of (A) with (B), and then assemble
cowl top covers LH (1) and RH (2).
CAUTION:
• Always replace cowl top cover EPT sealer on rear of vehicle with a new one when installing old cowl
top cover.
• After installing, perform adjustment of wiper arm. Refer to
.
JMKIA2160ZZ
JMKIA2161ZZ
FENDER PROTECTOR
EXT-25
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
FENDER PROTECTOR
FENDER PROTECTOR
FENDER PROTECTOR : Exploded View
INFOID:0000000003134291
FENDER PROTECTOR : Removal and Installation
INFOID:0000000003134292
REMOVAL
1.
Remove front fillet molding. Refer to
EXT-32, "Removal and Installation"
2.
Remove front fender (rear) fixing grommets (A) with remover
tool (B).
1.
Fender protector (rear)
2.
Fender protector (front)
3.
Splash guard
4.
Air guide
5.
J-nut
6.
Grommet
7.
Fender clip
8.
Front fender
9.
Splash guard (AWD)
JMKIA2162ZZ
JMKIA2164ZZ
EXT-26
< ON-VEHICLE REPAIR >
FENDER PROTECTOR
3.
Remove center mudguard (1) fixing screws (A).
4.
Remove center mudguard fixing bolt (B).
5.
Remove clips of fender protector (rear).
6.
Remove fender clip from wheel house arches, and then remove fender protector (rear) from wheel house.
7.
Remove front fender (front) fixing grommet (A) with remover tool
(B).
8.
Remove fender protector (front) fixing bolts (A).
9.
Remove fender protector (front) mounting clips.
10. Remove fender clip from wheel house arches, and then remove fender protector (front) from wheel house.
11. Remove the following parts after removing front fender protector.
• Air guide
• Fender clip
INSTALLATION
Install in the reverse order of removal.
REAR WHEEL HOUSE PROTECTOR
JMKIA2238ZZ
JMKIA2163ZZ
JMKIA0107GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст