Infiniti EX35. Manual — part 834
FRONT BUMPER
EXT-15
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
After installing, perform fitting adjustment.
JMKIA2144ZZ
Portion
Clearance
Flush
Front bumper – Front grille
A – A
0.2 – 2.8 mm (0.008 – 0.110 in)
—
Front bumper – Front grille
B – B
0.2 – 2.8 mm (0.008 – 0.110 in)
—
Front bumper – Hood
C – C
1.5 – 5.5 mm (0.059 – 0.217 in) - 1.0 – 3.0 mm (- 0.039 – 0.118 in)
Front bumper – Headlamp
D – D
0.3 – 3.2 mm (0.012 – 0.126 in)
—
Front bumper – Front fender
E – E
0.0 – 0.8 mm (0.000 – 0.031 in) - 0.2 – 1.8 mm (- 0.008 – 0.071 in)
EXT-16
< ON-VEHICLE REPAIR >
REAR BUMPER
REAR BUMPER
Exploded View
INFOID:0000000003134285
1.
Grommet
2.
Bumper side bracket A LH
3.
Bumper side bracket B LH
4.
Bumper stay LH
5.
Rear combination lamp LH
6.
Sonar sensor LH
7.
Bumper fascia assembly
8.
Sonar sensor RH
9.
Bumper side cover RH
JMKIA2145ZZ
REAR BUMPER
EXT-17
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
Removal and Installation
INFOID:0000000003134286
REMOVAL
CAUTION:
Bumper fascia is made of resin. Do not apply strong force to it, and be careful to prevent contact with
oil.
1.
Fully open back door.
2.
Remove bumper side cover (1) fixing clips and pawls, and then
remove bumper side cover (LH/RH).
3.
Remove rear combination lamp (LH/RH). Refer to
EXL-204, "Removal and Installation"
4.
Remove clip (A) and bolts (B) located under rear combination
lamp (LH/RH).
5.
Remove rear fillet molding (1) fixing screws (A) (LH/RH).
6.
Remove rear fillet molding fixing pawls and clip (LH/RH).
Refer to
EXT-32, "Removal and Installation"
.
10. Rear combination lamp RH
11.
Bumper side bracket A RH
12. Bumper side bracket B RH
13. Bumper lower retainer LH
14. Bumper stay RH
15. Bumper lower retainer RH
16. Bumper reinforcement
17. Energy absorber
18. Bumper sub harness
19. Bumper side cover LH
: Clip
: Pawl
JMKIA2149ZZ
JMKIA2150ZZ
: Clip
: Pawl
JMKIA2146ZZ
EXT-18
< ON-VEHICLE REPAIR >
REAR BUMPER
7.
Remove bumper fascia (1) fixing screws (A) (LH/RH).
8.
Remove clips (A) of bumper fascia underside.
9.
Pull to release bumper fascia assembly from bumper side
bracket.
10. Disconnect bumper sub harness connector (A).
11. Remove bumper fascia assembly.
CAUTION:
When removing bumper fascia, 2 workers are required so as to prevent it from dropping.
12. Remove the following parts after removing bumper fascia.
• Rear turn signal lamp (LH/RH). Refer to
EXL-205, "Removal and Installation"
.
• Sonar sensor. Refer to
SN-44, "REAR : Removal and Installation"
.
• Bumper sub harness
• Bumper side bracket A
• Bumper side bracket B
13. Remove bumper energy absorber.
14. Remove license lamp harness clamps of bumper reinforcement.
JMKIA2147ZZ
JMKIA2148ZZ
: Pawl
JMKIA2151ZZ
JMKIA2152ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст