Infiniti EX35. Manual — part 1303
SEC-108
< COMPONENT DIAGNOSIS >
[INTELLIGENT KEY SYSTEM]
B210F PNP/CLUTCH INTERLOCK SWITCH
B210F PNP/CLUTCH INTERLOCK SWITCH
Description
INFOID:0000000003586627
IPDM E/R confirms the shift position with the following signals.
• Park/neutral position (PNP) switch
• Shift position signal from BCM (CAN)
DTC Logic
INFOID:0000000003586628
DTC DETECTION LOGIC
NOTE:
If DTC B210F is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON under the following conditions and wait for at least 1 second.
-
Selector lever is in the P or N position.
-
Do not depress brake pedal.
2.
Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES
>> Go to
SEC-108, "Diagnosis Procedure"
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000003586629
1.
CHECK DTC WITH BCM
Check “Self diagnostic result” with CONSULT-III. Refer to
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK PNP SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector E5.
3.
Turn ignition switch ON.
4.
Check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-34, "Removal and Installation"
NO
>> GO TO 3.
3.
CHECK PNP SWITCH CIRCUIT
1.
Turn ignition switch OFF.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B210F
INTER LOCK/PNP SW
ON
IPDM E/R detects a mismatch between the sig-
nals below for 1 second or more.
• PNP switch input signal
• Shift position signal from BCM (CAN)
• Harness or connectors
[Park/neutral position (PNP) switch
circuit is open or shorted
• Park/neutral position (PNP) switch
(+)
(–)
Condition
Voltage (V)
(Approx.)
IPDM E/R
Connector
Terminal
E5
30
Ground
Selector lever
P or N
Battery voltage
Other than above
0
B210F PNP/CLUTCH INTERLOCK SWITCH
SEC-109
< COMPONENT DIAGNOSIS >
[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
2.
Disconnect TCM connector E5.
3.
Check continuity between IPDM E/R harness connector and TCM harness connector.
4.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness or connector.
4.
CHECK INTERMITTENT INCIDENT
GI-38, "Intermittent Incident"
.
>> INSPECTION END
IPDM E/R
TCM
Continuity
Connector
Terminal
Connector
Terminal
E5
30
F51
9
Existed
IPDM E/R
Ground
Continuity
Connector
Terminal
E5
30
Not existed
SEC-110
< COMPONENT DIAGNOSIS >
[INTELLIGENT KEY SYSTEM]
B2110 PNP/CLUTCH INTERLOCK SWITCH
B2110 PNP/CLUTCH INTERLOCK SWITCH
Description
INFOID:0000000003586630
IPDM E/R confirms the shift position with the following signals.
• Park/neutral position (PNP) switch
• Shift position signal from BCM (CAN)
DTC Logic
INFOID:0000000003586631
DTC DETECTION LOGIC
NOTE:
If DTC B2110 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn the ignition switch ON under the following conditions and wait for at least 1 second.
-
Selector lever is in the P or N position.
-
Do not depress brake pedal.
2.
Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES
>> Go to
SEC-110, "Diagnosis Procedure"
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000003586632
1.
CHECK DTC WITH TCM
Check “Self diagnostic result” with CONSULT-III. Refer to
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK PNP SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector E5.
3.
Turn ignition switch ON.
4.
Check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-34, "Removal and Installation"
NO
>> GO TO 3.
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B2110
INTER LOCK/PNP
SW
IPDM E/R detects mismatch between the signals
below for 1 second or more.
• PNP switch input signal
• Shift position signal from BCM (CAN)
• Harness or connectors
[Park/neutral position (PNP) switch
circuit is open or shorted
• Park/neutral position (PNP) switch
• IPDM E/R
• BCM
(+)
(–)
Condition
Voltage (V)
(Approx.)
IPDM E/R
Connector
Terminal
E5
30
Ground
Selector lever
P or N
Battery voltage
Other than above
0
B2110 PNP/CLUTCH INTERLOCK SWITCH
SEC-111
< COMPONENT DIAGNOSIS >
[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
3.
CHECK PNP SWITCH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect TCM connector.
3.
Check continuity between IPDM E/R harness connector and TCM harness connector.
4.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness or connector.
4.
CHECK INTERMITTENT INCIDENT
GI-38, "Intermittent Incident"
.
>> INSPECTION END
IPDM E/R
TCM
Continuity
Connector
Terminal
Connector
Terminal
E5
30
F51
9
Existed
IPDM E/R
Ground
Continuity
Connector
Terminal
E5
30
Not existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст