Infiniti EX35. Manual — part 982
INSTRUMENT PANEL ASSEMBLY
IP-13
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
[ ]: Number indicates step in removal procedures.
REMOVAL
1.
Put selector lever in drive position.
2.
Remove selector lever knob.
• Refer to
TM-156, "2WD : Removal and Installation"
• Refer to
TM-159, "AWD : Removal and Installation"
.(AWD models)
3.
Remove console finisher assembly.
• Pull console finisher (1), upward to disengage from center
console.
• Disconnect harness connectors.
4.
Disconnect console sub harness connectors (A).
5.
Remove center console fixing screws (B).
6.
Put front seat to front must position.
7.
Remove console rear finisher.
• Pull back the console rear finisher (1) with remover tool (A).
• Disconnect inside key antenna connector.
Front pillar garnish RH
[33]
Speaker grille RH
[34]
Instrument panel assembly
[35]
: Pawl
: Metal clip
JMJIA1612ZZ
JMJIA1613ZZ
: Metal clip
JMJIA1614ZZ
IP-14
< ON-VEHICLE REPAIR >
INSTRUMENT PANEL ASSEMBLY
8.
Remove rear ventilator duct (1).
Refer to
VTL-58, "REAR VENTILATOR DUCT 2 : Removal and
.
9.
Remove center console fixing screws (A).
10. Remove center console assembly.
• Lift up center console assembly back side.
• Disconnect harness connectors.
11. Put front seat to rear most position.
12. Remove instrument side finisher LH.
• Insert a remover tool into lower space.
• Pull the instrument side finisher LH (1) crosswise.
13. Remove instrument lower panel LH.
• Remove hood opener lever fixing bolts (A).
• Pull back instrument lower panel LH (1).
• Remove skirt clips of steering column lower cover (2).
• Release data link connector (pawl) then remove it from instru-
ment lower panel LH (1).
• Disconnect harness connectors and aspirator duct.
14. Remove steering wheel. Refer to
ST-16, "Removal and Installation"
.
JMJIA1615ZZ
: Clip
: Pawl
JMJIA1616ZZ
: Clip
: Pawl
: Metal clip
JMJIA1617ZZ
INSTRUMENT PANEL ASSEMBLY
IP-15
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
15. Remove steering column covers.
• Remove steering column mask (1).
• Remove steering column cover fixing screws (A).
• Pull up steering column upper cover (2), and then remove
steering column upper cover.
• Pull down steering column lower cover (3), and then remove
steering column lower cover.
• Disconnect ADP steering switch connector. (with ADP)
16. Remove combination switch. Refer to
BCS-85, "Removal and Installation"
17. Remove cluster lid A (upper).
• Pull back cluster lid A (upper) (1), and disengage pawls and
metal clips.
• Remove cluster lid A (upper).
18. Remove cluster lid A.
• Remove cluster lid A (1) fixing screws (A).
• Pull back cluster lid A, and disengage metal clips.
• Remove cluster lid A.
19. Remove combination meter. Refer to
MWI-162, "Removal and Installation"
.
: Clip
: Pawl
JMJIA1618ZZ
: Pawl
: Metal clip
JMJIA1619ZZ
: Metal clip
JMJIA1620ZZ
IP-16
< ON-VEHICLE REPAIR >
INSTRUMENT PANEL ASSEMBLY
20. Remove instrument harness (1) fixing clips (A).
21. Disconnect trip A/B reset switch (1) harness connector (A).
.
22. Remove front body side welt LH. Refer to
INT-20, "Removal and Installation"
.
23. Remove front pillar garnish LH. Refer to
INT-20, "Removal and Installation"
24. Disconnect antenna connectors (A).
25. Remove harness clip (B).
26. Remove speaker grille LH.
• Pull up and back speaker grille LH (1).
• Disconnect front squawker harness connector.
JMJIA1638ZZ
JMJIA1639ZZ
JMJIA1637ZZ
: Clip
: Pawl
JMJIA1621ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст