Infiniti EX35. Manual — part 706
COMPRESSION PRESSURE
EM-23
< ON-VEHICLE MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
COMPRESSION PRESSURE
Inspection
INFOID:0000000003139093
1.
Warm up engine thoroughly. Then, stop it.
2.
Release fuel pressure. Refer to
.
3.
Disconnect fuel pump fuse (1) from IPDM E/R (2) to avoid fuel
injection during measurement.
4.
Remove engine cover with power tool. Refer to
.
5.
Remove ignition coil and spark plug from each cylinder. Refer to
6.
Connect engine tachometer (not required in use of CONSULT-III).
7.
Install compression gauge with an adapter (commercial service
tool) onto spark plug hole.
• Use the adapter whose picking up end inserted to spark plug
hole is smaller than 20 mm (0.79 in) in diameter. Otherwise, it
may be caught by cylinder head during removal.
8.
With accelerator pedal fully depressed, turn ignition switch to “START” for cranking. When the gauge
pointer stabilizes, read the compression pressure and the engine rpm. Perform these steps to check each
cylinder.
CAUTION:
Always use a fully charged battery to obtain the specified engine speed.
• If the engine speed is out of the specified range, check battery liquid for proper gravity. Check the
engine speed again with normal battery gravity.
• If compression pressure is below minimum value, check valve clearances and parts associated with
combustion chamber (valve, valve seat, piston, piston ring, cylinder bore, cylinder head, cylinder head
gasket). After the checking, measure compression pressure again.
JMBIA0021ZZ
PBIC0900E
a
: 20 mm (0.79 in)
JPBIA0171ZZ
Compression pressure
: Refer to
EM-24
< ON-VEHICLE MAINTENANCE >
COMPRESSION PRESSURE
• If some cylinder has low compression pressure, pour small amount of engine oil into the spark plug hole
of the cylinder to re-check it for compression.
- If the added engine oil improves the compression, piston rings may be worn out or damaged. Check pis-
ton rings and replace if necessary.
- If the compression pressure remains at low level despite the addition of engine oil, valves may be mal-
functioning. Check valves for damage. Replace valve or valve seat accordingly.
• If two adjacent cylinders have respectively low compression pressure and their compression remains
low even after the addition of engine oil, cylinder head gaskets are leaking. In such a case, replace cyl-
inder head gaskets.
9.
After inspection is completed, install removed parts.
10. Start the engine, and check that the engine runs smoothly.
11. Perform trouble diagnosis. If DTC appears, erase it. Refer to
ENGINE COVER
EM-25
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
ON-VEHICLE REPAIR
ENGINE COVER
Exploded View
INFOID:0000000003470631
Removal and Installation
INFOID:0000000003470632
REMOVAL
Loosen mounting bolts and nuts in the reverse order as shown in the
figure, and then remove engine cover.
CAUTION:
Never damage or scratch engine cover when installing or
removing.
INSTALLATION
Install engine cover, and then tighten mounting bolts and nuts in
numerical order as shown in the figure.
CAUTION:
Never damage or scratch engine cover when installing or
removing.
1
: Engine cover
JPBIA0256GB
JPBIA1823ZZ
JPBIA1823ZZ
EM-26
< ON-VEHICLE REPAIR >
DRIVE BELT AUTO TENSIONER AND IDLER PULLEY
DRIVE BELT AUTO TENSIONER AND IDLER PULLEY
Exploded View
INFOID:0000000003139094
Removal and Installation
INFOID:0000000003139095
Removal
1.
Remove drive belt. Refer to
.
• Keep auto-tensioner pulley arm locked after drive belt is removed.
2.
Remove auto-tensioner and idler pulley. Refer to
• Keep auto-tensioner pulley arm locked to install or remove auto-tensioner.
Installation
Installation is the reverse order of removal.
CAUTION:
If there is damage greater than peeled paint, replace drive belt auto-tensioner.
1.
Front timing chain case
2.
Drive belt auto-tensioner
3.
Idler pulley
4.
Idler pulley
Refer to
for symbols in the figure.
JPBIA0004ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст